You are here
General discussion
Log in to post new content in the forum.
Topic / Topic starter |
Replies | Last post | |
|---|---|---|---|
|
3 Phase DC Motor and VESC by Mustard » Sun, 2021-05-23 19:03 |
1 |
by skyline1970 Sat, 2021-09-18 11:50 |
|
|
3 sensorless motors connected with belt by moose09876 » Wed, 2022-09-14 23:26 |
5 |
by moose09876 Fri, 2022-09-16 14:09 |
|
|
3 shunt low side vs 3 shunt 'in phase' current sensing by ripperpc » Mon, 2020-05-04 08:47 |
6 |
by bww129 Wed, 2020-05-27 17:59 |
|
|
3 speed switch by de-bodgery » Sat, 2021-08-21 02:22 |
17 |
by Oscar Lozano Gimenez Mon, 2023-05-22 14:07 |
|
|
3.3V/5V External Electronics Raspberry Pi by ed muthiah » Sun, 2020-07-19 16:38 |
1 |
by TheFallen Mon, 2020-07-20 15:15 |
|
|
360 Rotation Hall Sensors, would these work through ADC? by portnawake » Thu, 2018-06-07 02:37 |
3 |
by Roger Wolff Fri, 2018-06-15 08:50 |
|
|
3Shul 700A reporting negative current spikes by reobaird » Sat, 2023-03-25 03:22 |
0 |
by reobaird Mon, 2023-03-27 09:34 |
|
|
3Shul controller gokart by th3v3rn » Thu, 2024-01-18 07:14 |
0 |
by th3v3rn Thu, 2024-01-18 07:17 |
|
|
3v3 Regulator fried? How to check if STM was affected too? by Seudo » Fri, 2024-02-16 19:48 |
1 |
by bww129 Fri, 2024-03-15 05:36 |
|
|
4 fried vesc's Australia by adamclarke1985 » Tue, 2020-03-31 20:48 |
0 |
by adamclarke1985 Tue, 2020-03-31 21:24 |
|
|
4 vesc motors at once? by i-make-robots » Thu, 2020-04-16 02:17 |
1 |
by hexakopter Sat, 2020-04-18 12:20 |
|
|
4.12 cooling mod by thewho » Wed, 2019-05-01 18:45 |
0 |
by thewho Wed, 2019-05-01 18:45 |
|
|
4.12 HK VESC - Static blue LED and no usb Connection, HELP!! by plot1992 » Thu, 2018-08-02 19:01 |
5 |
by Frazatto Tue, 2018-08-28 15:43 |
|
|
4.2 hw Erpm bldc mode by Katt » Wed, 2021-01-27 15:48 |
2 |
by Katt Tue, 2021-02-02 14:16 |
|
|
48N32P sync loss by roque.canales » Fri, 2023-08-18 11:01 |
0 |
by roque.canales Fri, 2023-08-18 11:01 |
|
|
4kw BLDC hybrid system help by thardi10 » Tue, 2019-01-08 17:06 |
2 |
by frank Tue, 2019-01-15 22:15 |
|
|
4wd rover using hub-motors by mhyer » Thu, 2023-05-18 09:56 |
2 |
by velolac Tue, 2023-05-23 10:03 |
|
|
5.02 Firmware on Trampa VESC 6 MKVI? by maxhertz » Sun, 2023-01-15 13:58 |
2 |
by maxhertz Mon, 2023-01-16 00:24 |
|
|
5phase Vesc based on 75/300 by BartE » Thu, 2020-03-05 23:17 |
8 |
by vadicus Sun, 2020-03-08 05:51 |
|
|
5V/serial weirdness when using FOC by wihrl » Sat, 2019-06-15 12:57 |
1 |
by frank Fri, 2019-06-28 14:13 |
|
|
6 Phase Motor - How to Drive it? by vitormhenrique » Wed, 2020-02-19 05:47 |
2 |
by Badkad Fri, 2020-03-20 19:36 |
|
|
75 / 300 vesc by craig w » Thu, 2021-12-16 03:36 |
1 |
by electricfox Thu, 2021-12-16 15:29 |
|
|
75/250 question/issue by Petre Daniel Stroe » Sat, 2022-12-10 14:51 |
1 |
by frank Sat, 2022-12-10 21:13 |
|
|
75/300 connection issues FW3.6 by renaudbarbier » Fri, 2019-11-01 20:17 |
3 |
by frank Tue, 2019-11-05 09:18 |
|
|
75/300 Large inrunner problem (video) by dk-odense » Mon, 2019-11-04 21:53 |
1 |
by frank Tue, 2019-11-05 09:06 |
Log in to post new content in the forum.
