You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
2kW motor with VESS 75200 by Sazabi » Fri, 2024-04-05 11:17 |
0 |
by Sazabi Fri, 2024-04-05 11:18 |
|
|
Help with FOC/PID parameter by CTSchorsch » Thu, 2020-01-23 21:57 |
0 |
by CTSchorsch Thu, 2020-01-23 21:57 |
|
|
Dutycyle dropping under load by Julzz112 » Sun, 2024-04-14 18:31 |
0 |
by Julzz112 Tue, 2024-04-16 08:26 |
|
|
FSESC 75100 motor problem by anythingstl » Tue, 2024-02-13 17:15 |
0 |
by anythingstl Mon, 2024-02-19 19:23 |
|
|
Trying to read and set MCCONF by Jamie42 » Tue, 2020-03-24 19:47 |
0 |
by Jamie42 Tue, 2020-03-24 19:47 |
|
|
Vesc and Arduino Interface with ppm control???? by ruthvikchanda » Mon, 2018-09-10 12:01 |
0 |
by ruthvikchanda Mon, 2018-09-10 12:01 |
|
|
FAULT_CODE_DRV Motor not spinning by Mightyorc » Sat, 2018-09-15 03:36 |
0 |
by Mightyorc Sat, 2018-09-15 03:36 |
|
|
Install VESC on ubuntu 18.04 bionic by rest_vesc_001 » Tue, 2020-12-08 15:34 |
0 |
by rest_vesc_001 Tue, 2020-12-08 15:34 |
|
|
VESC specialist required. by BlackPanthera » Mon, 2022-07-18 17:11 |
0 |
by BlackPanthera Mon, 2022-07-18 17:11 |
|
|
How do you turn on traction control ( I can't remember) by msim2 » Fri, 2022-05-20 22:06 |
0 |
by msim2 Fri, 2022-05-20 22:06 |
|
|
Help with translating/converting hall sensor values from BLDC to FOC by theviith » Thu, 2018-10-11 09:47 |
0 |
by theviith Thu, 2018-10-11 09:47 |
|
|
VESC with asynchronous motors by afbbfa » Fri, 2022-07-29 22:51 |
0 |
by afbbfa Fri, 2022-07-29 22:51 |
|
|
I need clarification on connecting a Magura 0-5k Ohm Pot Twist Throttle to Tronic 250 VESC. by notahorse » Fri, 2022-06-03 08:13 |
0 |
by notahorse Fri, 2022-06-03 08:13 |
|
|
Sensorless FOC with Duty Cycle will not stop spinning by moose09876 » Mon, 2022-08-01 18:08 |
0 |
by moose09876 Mon, 2022-08-01 18:08 |
|
|
VESC as generator - settings confirmation by justinlsquire » Mon, 2022-06-06 02:44 |
0 |
by justinlsquire Mon, 2022-06-06 02:44 |
|
|
Maximize startup torque by arosenthal » Sat, 2020-11-14 14:16 |
0 |
by arosenthal Sat, 2020-11-14 14:17 |
|
|
Cannot connect to VESC via USB or SWD by hagis » Wed, 2020-09-23 17:21 |
0 |
by hagis Wed, 2020-09-23 17:21 |
|
|
VESC Setup - Fluctuating/Unstable Duty Cycle/eRPM/Current by liminalsunset » Thu, 2022-08-04 01:44 |
0 |
by liminalsunset Thu, 2022-08-04 01:44 |
|
|
Because..why not: Full Self Riding Skateboard (autonomous skateboard) by x78163 » Wed, 2022-06-08 17:33 |
0 |
by x78163 Wed, 2022-06-08 17:33 |
|
|
Tips on tuning PID for a 170mm RW170 hub motor, 15 pole-pairs, low speed, high torque, 0-3000 ERPM by PaulMakesThings » Fri, 2022-08-05 11:06 |
0 |
by PaulMakesThings Fri, 2022-08-05 11:06 |
|
|
Voltage spikes on BEMF scope by Sgw32 » Wed, 2020-11-18 16:03 |
0 |
by Sgw32 Wed, 2020-11-18 16:06 |
|
|
Hub motor FOC detection. by Roger Wolff » Tue, 2018-08-21 19:12 |
0 |
by Roger Wolff Tue, 2018-08-21 19:12 |
|
|
Best way to run a hoverboard motor that has an AB encoder and Hall sensors, but no index? by PaulMakesThings » Thu, 2022-06-23 23:43 |
0 |
by PaulMakesThings Thu, 2022-06-23 23:43 |
|
|
resistance and inductance value changes when each measurement by alexshen2012 » Fri, 2022-07-01 05:42 |
0 |
by alexshen2012 Fri, 2022-07-01 05:42 |
|
|
Does PLL measure the REAL motor speed by wyk » Mon, 2020-11-23 08:34 |
0 |
by wyk Mon, 2020-11-23 08:34 |
Log in to post new content in the forum.
