You are here
General discussion
Log in to post new content in the forum.
Topic / Topic starter |
Replies | Last post | |
|---|---|---|---|
|
Two phase modulation by jguy » Sat, 2023-12-09 13:33 |
4 |
by jguy Fri, 2023-12-15 11:49 |
|
|
Two Motors on same Shaft by Giga93 » Thu, 2017-12-14 10:12 |
5 |
by ThierryGTLTS Sun, 2017-12-17 13:20 |
|
|
Tuning strategy for a large motor? by MrSurly » Tue, 2022-11-01 06:51 |
1 |
by vadicus Mon, 2022-11-14 18:23 |
|
|
Tuning prop loads with rapid erpm increase in duty cycle or speed control by mirage98 » Mon, 2022-09-26 01:51 |
1 |
by drummerboy5408 Mon, 2022-10-24 05:49 |
|
|
Tuning process? by wingborne » Tue, 2020-09-29 00:09 |
0 |
by wingborne Tue, 2020-09-29 21:39 |
|
|
tuning PID speed for the skateboard motor with hall sensors by salviador » Tue, 2021-09-14 14:37 |
1 |
by skyline1970 Sat, 2021-09-18 11:18 |
|
|
tuning low kv high pole sensorless outrunner by cdlapoin » Tue, 2025-05-20 22:14 |
3 |
by flagoworld Wed, 2025-12-10 19:29 |
|
|
Tuning Advanced Settings For BLDC by DjSourD » Wed, 2020-08-26 05:51 |
1 |
by trademarkaaron Tue, 2023-11-28 18:42 |
|
|
Trying to run a refrigerant compressor's BLDC with VESC by logansheaf » Wed, 2025-01-29 02:01 |
2 |
by logansheaf Wed, 2025-01-29 23:23 |
|
|
Trying to read and set MCCONF by Jamie42 » Tue, 2020-03-24 19:47 |
0 |
by Jamie42 Tue, 2020-03-24 19:47 |
|
|
Trying to make motor-control work for predetermined motions, could use some help by Davideo » Fri, 2019-08-16 01:20 |
1 |
by s0313045 Mon, 2019-08-19 05:12 |
|
|
trying to get torque with speed (flipsky 75100) by Trecit0n » Fri, 2025-08-01 21:19 |
4 |
by Trecit0n Tue, 2025-08-12 00:05 |
|
|
Trouble with Sensorless Startup on Trampa 6376 160Kv Motors (VESC 6 Dual, FW 6.05) by bojfik » Mon, 2025-05-26 14:35 |
1 |
by bojfik Tue, 2025-05-27 15:51 |
|
|
Trouble Detecting ABI Encoder on VESC6/75 by jonathansel » Fri, 2022-10-07 22:34 |
0 |
by jonathansel Fri, 2022-10-07 22:34 |
|
|
Trapezoidal/ s curve trajectory/"Position Mode" RPM control of BLDC motor by Vishwa Brahmaiah » Fri, 2019-05-24 18:22 |
1 |
by jelliesejecta Sat, 2019-09-14 10:31 |
|
|
Trampa VESC6 USB connectivity problem caused by usb hub? by hagoston » Tue, 2021-06-01 10:27 |
4 |
by hagoston Wed, 2021-06-02 09:27 |
|
|
Trampa VESC 100/250 suitable for heavy applications? by nojjan » Thu, 2022-12-29 13:52 |
9 |
by vadicus Wed, 2023-03-01 06:26 |
|
|
Trampa 100/250 with one old brushed DC motor....how can i change the motor spin direction????plz help!!! by Asi » Fri, 2022-11-18 12:45 |
3 |
by frank Sat, 2022-11-19 14:55 |
|
|
Trampa 100/250 with Cyc x1pro motor high Rpm issue PLZ Help :) by Asi » Thu, 2022-07-28 10:08 |
2 |
by Asi Thu, 2022-07-28 16:12 |
|
|
trampa by badger1666 » Mon, 2017-12-11 22:37 |
5 |
by wdaehn Wed, 2017-12-13 12:17 |
|
|
Touchy ADC Connector by ebikerevolution » Thu, 2018-05-10 00:40 |
1 |
by Roger Wolff Thu, 2018-05-10 22:08 |
|
|
Torque Ramp Rate whilst in FOC by J_W97 » Mon, 2022-03-14 11:50 |
1 |
by skyline1970 Mon, 2022-03-14 20:29 |
|
|
Torque control with PWM at 10kHz for LinuxCNC + MESA + AC servo by antonchromjak » Tue, 2018-03-06 08:01 |
6 |
by Artabotak Sat, 2024-01-06 09:24 |
|
|
Torque control setting by mambazhasa@uni.... » Thu, 2023-01-26 17:24 |
3 |
by Davidepolpi91 Tue, 2024-03-19 12:45 |
|
|
Too little torque. by Roger Wolff » Thu, 2018-05-10 18:11 |
4 |
by Roger Wolff Mon, 2018-05-14 19:30 |
Log in to post new content in the forum.
