You are here
General discussion
Log in to post new content in the forum.
Topic / Topic starter |
Replies | Last post | |
|---|---|---|---|
|
Can't get motor to run using COMM port on vesc 6 MKVI and arduino mega with a potentiometer and SolidGeeks UART library by Kokonenen » Thu, 2023-03-30 11:41 |
1 |
by Kokonenen Thu, 2023-03-30 16:19 |
|
|
can't reach the maximum speed by kingpon » Sat, 2017-10-28 04:55 |
3 |
by elektrinis Tue, 2018-04-17 21:50 |
|
|
Can't receive status message via CAN bus by IanG » Mon, 2020-04-13 03:50 |
4 |
by olivierabristol Sun, 2022-02-27 08:31 |
|
|
Can't start a sensorless motor of a scooter by tobe81cwb » Mon, 2022-05-02 03:25 |
1 |
by skyline1970 Thu, 2022-11-24 21:36 |
|
|
Canbus slave control in duty cycle mode not working correctly by Enak » Sat, 2019-04-13 03:55 |
1 |
by benjamin Mon, 2019-04-15 10:09 |
|
|
Cannot change CAN Baudrate, Maytech SUPERFOC6.8 by sivanhere » Thu, 2023-03-23 08:12 |
5 |
by frank Mon, 2023-03-27 09:28 |
|
|
Cannot connect to VESC via USB or SWD by hagis » Wed, 2020-09-23 17:21 |
0 |
by hagis Wed, 2020-09-23 17:21 |
|
|
Cannot downgrade from 5.03 to 5.02 by kallep » Sat, 2022-02-26 19:08 |
5 |
by frank Sat, 2022-03-12 12:09 |
|
|
Cannot reach max speed of BLDC motor by rousha42 » Wed, 2021-11-03 20:23 |
4 |
by frank Tue, 2021-11-09 09:46 |
|
|
Cannot use BLE in combination with Custom App anymore after upgrading by Gatze » Wed, 2021-10-06 12:27 |
1 |
by Gatze Thu, 2021-10-21 10:21 |
|
|
CanOpen by maxmertins » Mon, 2023-01-30 17:10 |
4 |
by maxmertins Wed, 2023-02-01 17:24 |
|
|
Cant connect to Flipsky 75100 by Ed222 » Sun, 2022-03-20 00:31 |
5 |
by wimleo Wed, 2025-03-19 17:51 |
|
|
Cant get Rotor position to work by nancio » Mon, 2022-06-06 20:47 |
3 |
by frank Thu, 2022-06-09 09:05 |
|
|
CAN_PACKET_STATUS_5 Current IN and Fault code by matrixgti » Tue, 2019-06-11 12:24 |
1 |
by STTS Fri, 2021-08-13 09:09 |
|
|
Change RPM of motor by Gas_Sn4ke » Wed, 2019-01-16 03:51 |
2 |
by Shaik Siraaj Thu, 2019-01-17 11:14 |
|
|
Changing the timer for VESC auto turn off timing by dsuresh » Mon, 2021-03-15 21:19 |
0 |
by dsuresh Mon, 2021-03-15 21:19 |
|
|
Charge wires by Phill Dixon » Tue, 2017-10-24 14:24 |
4 |
by linsus Tue, 2017-11-21 14:39 |
|
|
choice between 2 eRPM by elektrojodler » Thu, 2022-05-05 15:22 |
3 |
by drummerboy5408 Tue, 2022-05-10 04:11 |
|
|
Choppiness in motor after half throttle by popeye243 » Tue, 2020-08-04 04:04 |
5 |
by vadicus Tue, 2020-09-15 23:53 |
|
|
combination current control and PID by elektrojodler » Thu, 2022-04-28 08:35 |
1 |
by notahorse Fri, 2022-07-15 22:28 |
|
|
command in power by Flyingtux » Thu, 2021-08-26 18:00 |
1 |
by skyline1970 Sat, 2021-09-18 11:31 |
|
|
Comms plug and leads by craig w » Fri, 2021-12-24 00:25 |
0 |
by craig w Fri, 2021-12-24 00:25 |
|
|
Communication with Vesc Tools by faheemift » Tue, 2021-02-09 16:08 |
8 |
by beatrixena Sat, 2021-02-20 09:11 |
|
|
Compatibility Question by Alexandre Borowczyk » Wed, 2020-09-16 20:06 |
1 |
by vadicus Wed, 2020-09-16 21:17 |
|
|
Compatibility with BiSS-C absolute encoder by wisllayvitrio » Sat, 2021-05-15 23:39 |
0 |
by wisllayvitrio Sat, 2021-05-15 23:40 |
Log in to post new content in the forum.
