You are here
General discussion
Log in to post new content in the forum.
Topic / Topic starter | Replies | Last post | |
---|---|---|---|
Can bus and BLDC vs FOC by Torbjorn » Fri, 2022-11-11 11:08 |
4 |
by Torbjorn Tue, 2022-11-15 14:37 |
|
Can bus communication. by Piamen » Wed, 2019-11-27 06:47 |
0 |
by Piamen Wed, 2019-11-27 06:47 |
|
CAN Bus Control by External Host by josh » Fri, 2018-11-30 06:43 |
3 |
by Jack_Li Mon, 2019-07-01 10:37 |
|
CAN bus rate, Flipsky Mini FSESC6.7 by christian.lees » Tue, 2022-01-18 22:57 |
0 |
by christian.lees Tue, 2022-01-18 22:57 |
|
Can control Vesc 100/250 by David_1 » Sat, 2022-06-18 01:31 |
1 |
by David_1 Sun, 2022-06-19 19:44 |
|
CAN eRPM report by alxsfrm » Mon, 2022-02-07 11:01 |
0 |
by alxsfrm Mon, 2022-02-07 11:01 |
|
Can I change control mode on the fly through the UART port? by spork » Wed, 2019-03-13 02:24 |
2 |
by spork Wed, 2019-03-13 15:41 |
|
Can i change the controller (LQFP64) with (LQFP100) with same Firmware? by GalihRiddle » Thu, 2019-09-05 13:44 |
2 |
by GalihRiddle Mon, 2019-09-09 13:22 |
|
can I fit a VESC in my e-skate? by 6diegodiego9 » Thu, 2021-01-21 20:42 |
1 |
by skyline1970 Tue, 2021-02-02 21:30 |
|
Can I use 12V power supply? by ryde6 » Sun, 2021-04-25 08:19 |
2 |
by vadicus Wed, 2021-07-14 21:01 |
|
Can larger BLDC motors be controlled with VESC? by Heimfried » Sun, 2020-02-02 21:29 |
3 |
by Heimfried Thu, 2020-02-06 22:39 |
|
Can motor parameters be detected with shaft load? by powerlabor001 » Thu, 2018-03-15 13:24 |
4 |
by powerlabor001 Sat, 2018-03-24 03:07 |
|
Can not adjust the RPM on my 1350 w motor by Arne Norway » Wed, 2019-01-09 18:47 |
6 |
by sam.vanratt Sun, 2019-01-13 13:36 |
|
Can not run again after run perfectly !! Pls help by Streetstar69 » Tue, 2021-11-23 03:03 |
1 |
by frank Tue, 2021-11-23 10:03 |
|
can not start motor with high duty by qdxiatao » Sat, 2018-03-24 03:58 |
0 |
by qdxiatao Sat, 2018-03-24 03:58 |
|
Can someone help me understand why I've burned up a DRV8302 in less than 10 seconds? by shimdidly » Fri, 2017-10-13 02:01 |
3 |
by shimdidly Mon, 2017-10-16 17:13 |
|
Can someone please post the steps to do position control from vesc tool? by dp » Wed, 2022-02-16 14:51 |
1 |
by frank Wed, 2022-02-16 17:24 |
|
CAN STATUS INTERRUPTS MOTOR OUTPUT by v1n23nt » Tue, 2022-03-15 09:06 |
0 |
by v1n23nt Tue, 2022-03-15 09:10 |
|
Can VESC be in parallel connection with BMS while being charged? by dfelz » Tue, 2020-06-16 21:47 |
1 |
by TheFallen Wed, 2020-06-17 16:03 |
|
Can you switch censored to sensor less or HFI by diyRick » Wed, 2021-06-30 23:43 |
2 |
by drdrs Wed, 2021-07-07 07:11 |
|
Can you use both axes on a 2-axis nunchuck/joystick controller with VESC? by adamdorr » Tue, 2019-12-31 22:05 |
6 |
by sanketh1691 Sat, 2021-10-09 00:45 |
|
can't communicate with arduino nrf by m.juan » Mon, 2018-07-02 16:57 |
0 |
by m.juan Mon, 2018-07-02 16:57 |
|
Can't connect to VESC's? Linux, need help? by ex-Gooserider » Wed, 2020-08-12 04:38 |
4 |
by ex-Gooserider Wed, 2020-08-19 01:39 |
|
Can't download files from my account by STTrife » Sat, 2021-05-01 19:21 |
0 |
by STTrife Sat, 2021-05-01 19:21 |
|
Can't find Configurable FOC current filter in VESC TOOL by e-biker » Sun, 2018-04-08 12:18 |
2 |
by e-biker Sun, 2018-04-08 12:55 |
Log in to post new content in the forum.