You are here
General discussion
Log in to post new content in the forum.
Topic / Topic starter |
Replies | Last post | |
|---|---|---|---|
|
What is limiting my RPMS (VESC 4.2 / Q100H setup) by nckbutler » Tue, 2020-03-03 15:37 |
1 |
by socrace Thu, 2020-03-05 03:50 |
|
|
What is limiting the speed? by ProgramThyself » Wed, 2021-10-06 20:07 |
7 |
by ProgramThyself Sun, 2021-10-17 19:08 |
|
|
what is the best vesc For long-term sea observation by jhgjg » Thu, 2022-09-22 12:12 |
5 |
by frank Mon, 2022-09-26 15:44 |
|
|
What is the best way to make an emergency button to stop the motor from spinning? by kdomanski » Sat, 2021-01-30 14:18 |
5 |
by skyline1970 Mon, 2021-02-01 21:25 |
|
|
What is the current state of mcus support? by il_piccione » Fri, 2025-04-25 09:47 |
0 |
by il_piccione Fri, 2025-04-25 09:47 |
|
|
what is this part for by ynoo443 » Wed, 2024-10-23 16:57 |
3 |
by ynoo443 Wed, 2024-10-23 17:02 |
|
|
What motors can i use with the vesc? by bengce » Sun, 2020-06-14 22:28 |
0 |
by bengce Sun, 2020-06-14 22:28 |
|
|
What Software to plan custom VESC by Plermpel » Mon, 2019-09-30 22:16 |
1 |
by frank Tue, 2019-10-01 10:29 |
|
|
What temerpature sensor and how do I use it? by evoheyax » Wed, 2018-08-29 19:22 |
3 |
by Danny Bokma Thu, 2018-08-30 19:12 |
|
|
What VESC Controller should I buy? by Skye Parker » Sat, 2023-03-04 07:10 |
1 |
by frank Mon, 2023-03-06 17:14 |
|
|
What's general algorithm of firmware? by Furkan Kaşku » Mon, 2020-02-10 09:20 |
1 |
by vadicus Mon, 2020-02-10 10:20 |
|
|
What's the PCB dimension of the VESC 6? by darwinbeing » Fri, 2018-04-06 06:52 |
2 |
by darwinbeing Thu, 2023-08-03 21:11 |
|
|
What's wrong with my motors? by Mads7400 » Fri, 2020-05-08 15:05 |
1 |
by tylr_r Wed, 2020-07-15 01:22 |
|
|
Wheel speed over CANBUS by paule » Tue, 2020-12-29 13:04 |
0 |
by paule Tue, 2020-12-29 13:04 |
|
|
wheelchair with a joystick via Vesc by hopeingod » Fri, 2024-05-17 12:00 |
0 |
by hopeingod Fri, 2024-05-17 12:00 |
|
|
Wheels only rotate about a quarter of a turn by Appearance » Mon, 2021-10-04 17:57 |
2 |
by drummerboy5408 Wed, 2021-10-13 05:08 |
|
|
When I mount the propeller on the motor ,I get a new promblem by moto_guy » Sat, 2019-03-02 05:16 |
0 |
by moto_guy Sat, 2019-03-02 05:16 |
|
|
when speed of vesc motor too fast and the arduino pin signal is unstable by HumorLogic » Tue, 2021-04-06 14:21 |
3 |
by woliam Sat, 2021-04-10 15:17 |
|
|
When SWD Program Connect Fails by canoeman » Mon, 2022-02-28 18:32 |
0 |
by canoeman Mon, 2022-02-28 18:32 |
|
|
Where can I ask technical questions about products? by MrSurly » Tue, 2022-04-19 05:22 |
0 |
by MrSurly Tue, 2022-04-19 05:22 |
|
|
Where to connect the Button for Reverse driver?, in ADC mode (Ebike throttle) by Astropower » Sun, 2019-05-19 22:10 |
3 |
by hackish Sun, 2019-09-08 05:31 |
|
|
Where to find CAN protocol documentation? by doctarr » Tue, 2020-12-29 15:33 |
0 |
by doctarr Tue, 2020-12-29 15:33 |
|
|
where to source BLDC 6.5in geared wheel? by fourchette » Thu, 2018-11-08 00:05 |
3 |
by fourchette Mon, 2018-11-19 22:54 |
|
|
Which App to use and how to wire it by philboslaggins » Sat, 2022-11-05 16:20 |
2 |
by nando Fri, 2025-08-29 15:19 |
|
|
which configuration file I should change to make operate a VESC at 800 Volts by JCordova » Tue, 2024-02-06 17:49 |
1 |
by NOAI Wed, 2024-02-07 15:54 |
Log in to post new content in the forum.
