You are here
General discussion
Log in to post new content in the forum.
Topic / Topic starter |
Replies | Last post | |
|---|---|---|---|
|
Sensorless FOC with Duty Cycle will not stop spinning by moose09876 » Mon, 2022-08-01 18:08 |
0 |
by moose09876 Mon, 2022-08-01 18:08 |
|
|
Sensorless mode with brushless motor with no sensor by focy » Wed, 2019-12-04 09:05 |
1 |
by frank Thu, 2019-12-05 11:07 |
|
|
Sensorless Startup Motor Cogging by Swinde12 » Sun, 2018-12-16 06:12 |
2 |
by Swinde12 Tue, 2018-12-18 19:05 |
|
|
Sensorless Transition and Deadtime Distortion by vadicus » Wed, 2020-09-16 21:54 |
3 |
by vadicus Tue, 2020-10-13 07:29 |
|
|
Sensorless tuning tips on bicycle hub motor by kalvdans » Sat, 2021-06-12 11:51 |
2 |
by neo Tue, 2021-06-15 02:02 |
|
|
Separate Deadband for ADC2? by striderkent » Wed, 2019-01-23 16:31 |
0 |
by striderkent Wed, 2019-01-23 16:31 |
|
|
Serial Connection Lost with Vesc6.6 Firmware 5.2 and Vesc Tool 3.0 by Dan Slanker » Wed, 2021-04-28 16:56 |
9 |
by AngelKillR Wed, 2022-09-28 05:10 |
|
|
Servo Mode / ODrive on VESC by JulianT » Tue, 2020-02-04 09:19 |
0 |
by JulianT Tue, 2020-02-04 09:19 |
|
|
Servo output CAN Formats by vinci » Mon, 2022-04-18 15:35 |
0 |
by vinci Mon, 2022-04-18 15:35 |
|
|
Servo output control by 007trains » Fri, 2021-05-14 15:16 |
3 |
by BalorNG Wed, 2021-06-30 19:42 |
|
|
Set and measure RPM - Questions by Piep » Thu, 2018-11-08 16:10 |
0 |
by Piep Thu, 2018-11-08 16:10 |
|
|
Set and store Current limit via Canbus by matrixgti » Mon, 2019-08-19 23:13 |
3 |
by Rbz Sun, 2020-05-31 13:44 |
|
|
Set current - is it input or phase current? by aegidius » Sun, 2026-02-08 05:58 |
0 |
by aegidius Sun, 2026-02-08 05:58 |
|
|
Set McConf with no values --> bootloader erased? by Kakskiv » Tue, 2017-11-28 12:52 |
3 |
by basti30 Wed, 2018-08-22 22:22 |
|
|
Set RPM - reverse direction over CAN-Bus by 65273 » Tue, 2022-03-29 14:49 |
4 |
by 65273 Fri, 2022-04-01 15:53 |
|
|
Setting PI / PID controllers in VESC for very low speeds. For CNC by K@RLSON » Sat, 2020-01-25 21:06 |
9 |
by Luke264 Wed, 2021-02-17 18:52 |
|
|
Setting PID gains (and other config parameters) over CAN Bus by TheCuriousRobot » Thu, 2022-12-15 22:03 |
0 |
by TheCuriousRobot Thu, 2022-12-15 22:03 |
|
|
Setting RPM over UART by klay2000 » Sat, 2024-06-29 01:27 |
0 |
by klay2000 Sat, 2024-06-29 01:28 |
|
|
Setting the motor parameters by Lenar » Sat, 2024-05-04 10:18 |
0 |
by Lenar Sat, 2024-05-04 10:18 |
|
|
Setting up flipsky by JanneHooo » Sat, 2023-10-14 13:07 |
2 |
by JanneHooo Sun, 2023-10-15 13:18 |
|
|
Setting up low KV brushless motor? by Trent » Sun, 2019-12-01 02:09 |
4 |
by Trent Wed, 2019-12-04 07:54 |
|
|
Settings by aquamarin » Sat, 2023-07-01 16:11 |
0 |
by aquamarin Sat, 2023-07-01 16:11 |
|
|
SETUP FOR SINGLE BRUSHED MOTOR by mmatthews@aquav... » Fri, 2022-05-13 01:57 |
1 |
by skyline1970 Thu, 2022-11-24 21:39 |
|
|
Should I drive a HDD motor with VESC or some other chip? by arildj78 » Tue, 2018-05-22 09:09 |
1 |
by arildj78 Wed, 2018-05-23 12:26 |
|
|
Shutdown mode by Akeela23 » Sat, 2023-05-06 01:50 |
1 |
by Akeela23 Sat, 2023-05-06 01:56 |
Log in to post new content in the forum.
