You are here
General discussion
Log in to post new content in the forum.
Topic / Topic starter |
Replies | Last post | |
|---|---|---|---|
|
FSESC 6.6 not Connecting to VESC Tool by billyredwood01 » Sat, 2020-11-28 12:34 |
12 |
by JP Mon, 2023-04-03 13:02 |
|
|
FSESC 75100 motor problem by anythingstl » Tue, 2024-02-13 17:15 |
0 |
by anythingstl Mon, 2024-02-19 19:23 |
|
|
FSESC 75100 repair by BDJ » Fri, 2022-06-24 21:02 |
1 |
by skyline1970 Thu, 2022-11-24 21:22 |
|
|
FSESC 75350 UNBALANCED_CURRENTS fault at higher loads by colmor » Thu, 2025-05-01 01:21 |
1 |
by erider Thu, 2025-10-09 07:55 |
|
|
FSESC6.6 and Rpi via UART - Understanding the software by gabrielredding » Sat, 2019-07-06 02:50 |
3 |
by abrac Mon, 2019-07-29 14:11 |
|
|
FSESC6.6+ Over Voltage Fault 80mm Motors by Yomiel » Fri, 2020-03-20 03:45 |
4 |
by TheFallen Mon, 2021-03-01 16:47 |
|
|
Full power at half throttle :( by TheFox » Wed, 2024-06-12 23:38 |
1 |
by TheFox Thu, 2024-06-13 22:20 |
|
|
Full Throttle direct after input deadband by toerde » Sat, 2022-04-30 18:54 |
4 |
by frank Mon, 2022-05-09 08:22 |
|
|
FW Vesc-Tool V0.95 by Meche » Mon, 2018-07-09 21:07 |
1 |
by Meche Wed, 2018-07-11 16:29 |
|
|
FW=ADC1, REV=ADC2 by ProgramThyself » Sat, 2020-08-01 23:30 |
4 |
by ProgramThyself Mon, 2020-08-03 03:56 |
|
|
G60 motor hall wires pinout by Talonkid119 » Wed, 2024-03-06 03:43 |
0 |
by Talonkid119 Wed, 2024-03-06 03:43 |
|
|
General help by jskessel » Tue, 2024-07-16 20:09 |
0 |
by jskessel Tue, 2024-07-16 20:09 |
|
|
General question on tuning vesc by stevo11811 » Wed, 2021-06-02 05:06 |
0 |
by stevo11811 Wed, 2021-06-02 05:12 |
|
|
Get values from slave VESC by Snabelost » Mon, 2023-08-07 08:54 |
1 |
by Snabelost Mon, 2023-08-07 13:21 |
|
|
Getting a specified rpm via ROS node by Owl Robot » Fri, 2022-05-20 17:38 |
1 |
by x78163 Wed, 2022-06-08 19:21 |
|
|
Getting IMU Data over UART by Mido » Wed, 2021-04-21 12:30 |
7 |
by MrFobwatch Fri, 2024-03-15 03:05 |
|
|
Getting Started / Prototyping Help by harrym » Wed, 2020-04-01 17:56 |
4 |
by javmarina Sat, 2020-05-09 17:35 |
|
|
Getting started with bus control of the VESC by Invert » Mon, 2018-05-21 12:04 |
3 |
by PM Thu, 2018-05-31 18:38 |
|
|
GO-FOC G300 - shorted the USB connector shield to 72v by hedbrant » Tue, 2023-04-11 13:22 |
1 |
by hedbrant Thu, 2023-04-13 20:44 |
|
|
Gokart project with Dual VESC 75V /100A by spacewalker » Mon, 2020-12-07 10:08 |
2 |
by spacewalker Tue, 2020-12-08 07:06 |
|
|
Golden Motor HPM48-5000, reconciling winding R & L values by j.konrad » Sat, 2022-01-15 22:09 |
24 |
by j.konrad Mon, 2022-01-31 15:15 |
|
|
Golden Motor with VESC 100/250 by dmitrymp3 » Thu, 2023-12-28 18:53 |
1 |
by electricfox Sat, 2023-12-30 11:24 |
|
|
Got the judders by Phill Dixon » Sun, 2018-05-13 17:45 |
0 |
by Phill Dixon Sun, 2018-05-13 17:45 |
|
|
GPDrive as AC current source by jdn2 » Tue, 2019-10-15 14:22 |
1 |
by frank Thu, 2019-10-17 11:14 |
|
|
GPIO Pins on VESC? by phils » Sat, 2022-10-22 17:58 |
2 |
by istvan.szell@gm... Tue, 2024-09-17 12:07 |
Log in to post new content in the forum.
