You are here
General discussion
Log in to post new content in the forum.
Topic / Topic starter | Replies | Last post | |
---|---|---|---|
rpm fail in FOC sensor mode by mansi712 » Thu, 2024-09-26 19:51 |
0 |
by mansi712 Thu, 2024-09-26 19:51 |
|
Using UART for FSESC by Kostya1875 » Thu, 2024-09-26 19:07 |
0 |
by Kostya1875 Thu, 2024-09-26 19:07 |
|
Strange controller behavior after experimenting by Deguello » Thu, 2024-09-12 07:59 |
1 |
by ricma Tue, 2024-09-24 21:55 |
|
Current mismatch between power supply and vesc tool by mansi712 » Tue, 2024-09-24 13:02 |
0 |
by mansi712 Tue, 2024-09-24 18:08 |
|
Lispscript help by mrendu43 » Mon, 2024-04-01 09:57 |
1 |
by woozie Mon, 2024-09-23 22:53 |
|
Differential steering setup by GCTech » Sat, 2020-07-04 17:38 |
4 |
by CalLangford Fri, 2024-09-20 20:29 |
|
Large robot servo controller with VESC, how to set up position control by kisdia » Thu, 2024-09-19 17:47 |
0 |
by kisdia Thu, 2024-09-19 17:47 |
|
FAULT_CODE_HIGH_OFFSET_CURRENT_SENSOR_3 by TB_Poule » Sat, 2021-04-10 17:26 |
10 |
by Mohanangappan Wed, 2024-09-18 16:20 |
|
GPIO Pins on VESC? by phils » Sat, 2022-10-22 17:58 |
2 |
by istvan.szell@gm... Tue, 2024-09-17 12:07 |
|
Can’t connect VESC tool to my ESC. Pls help by Comeback10 » Mon, 2024-09-16 23:08 |
0 |
by Comeback10 Mon, 2024-09-16 23:08 |
|
Dual g-foc300 setup help!!! by Re60s » Sat, 2024-09-07 09:12 |
3 |
by Tim Read Thu, 2024-09-12 16:42 |
|
24 Volt LiFePO by Vaxinius » Tue, 2024-09-10 16:34 |
0 |
by Vaxinius Tue, 2024-09-10 16:35 |
|
speed by ELRIOP » Sun, 2024-09-08 15:24 |
0 |
by ELRIOP Sun, 2024-09-08 15:24 |
|
VESC Express TCP connect with iOS not possible by johannes.b » Mon, 2024-09-02 19:51 |
2 |
by johannes.b Sat, 2024-09-07 13:56 |
|
Reverse Button Status over UART? by Rich235 » Sat, 2024-09-07 10:34 |
0 |
by Rich235 Sat, 2024-09-07 10:34 |
|
VESC 75/300 and EMC Tests for motorcycle conversion by gotfatalErrs » Tue, 2020-06-02 18:34 |
8 |
by Bubu54 Wed, 2024-09-04 13:52 |
|
Advice needed: How to select KV value (or: how important is KV, in reality?) by c0d3z3r0 » Tue, 2024-09-03 09:23 |
0 |
by c0d3z3r0 Tue, 2024-09-03 09:23 |
|
How to connect 5 Pin Hall Sensor to 6 Pin Hall Sensor Connector by tinytuna38 » Thu, 2024-06-20 20:56 |
1 |
by DaganWal Fri, 2024-08-30 00:53 |
|
HFI with PPM in Duty Cycle by DaganWal » Fri, 2024-08-30 00:30 |
0 |
by DaganWal Fri, 2024-08-30 00:30 |
|
HFI and a big in-runner? 65121 Motor and Flipsky 75200 Pro V2 ESC. by ajtalbot1 » Thu, 2024-08-22 20:18 |
5 |
by ajtalbot1 Tue, 2024-08-27 20:27 |
|
Issues with running bldc motor (Motor screeching) by mansi712 » Mon, 2024-08-26 12:10 |
0 |
by mansi712 Tue, 2024-08-27 18:42 |
|
Issues with STR500 tuning and calibration by Swapnil Inamdar » Thu, 2024-08-15 10:39 |
1 |
by electricfox Sun, 2024-08-25 12:00 |
|
Canoe fun! Running rough/stepping at low speeds, 75200 Pro V2 ESC and 65121 Motor. by ajtalbot1 » Wed, 2024-07-31 05:49 |
8 |
by ajtalbot1 Sat, 2024-08-17 23:44 |
|
VESC PAS and ADC App - How does it work? by numbke » Fri, 2023-02-24 23:49 |
7 |
by ml4050 Sat, 2024-08-17 23:30 |
|
VESC with Ey4 and special function by MachWas » Mon, 2024-08-12 02:34 |
0 |
by MachWas Mon, 2024-08-12 02:34 |
Log in to post new content in the forum.