You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
GPIO Pins on VESC? by phils » Sat, 2022-10-22 17:58 |
2 |
by istvan.szell@gm... Tue, 2024-09-17 12:07 |
|
|
FAULT_CODE_HIGH_OFFSET_CURRENT_SENSOR_3 by TB_Poule » Sat, 2021-04-10 17:26 |
10 |
by Mohanangappan Wed, 2024-09-18 16:20 |
|
|
Differential steering setup by GCTech » Sat, 2020-07-04 17:38 |
4 |
by CalLangford Fri, 2024-09-20 20:29 |
|
|
encoder detection error by qdxiatao » Wed, 2018-05-09 12:04 |
1 |
by mona Thu, 2024-10-10 15:55 |
|
|
150KW VESC by paltatech » Sun, 2017-09-10 23:11 |
40 |
by Artabotak Wed, 2024-11-27 11:15 |
|
|
SINE/COS encoder makes motor not work by DHOUT » Mon, 2023-01-30 05:23 |
1 |
by Jamesstudio Sun, 2024-12-01 17:56 |
|
|
position control with gearbox by raess » Tue, 2018-09-25 23:48 |
19 |
by Artabotak Tue, 2024-12-03 08:48 |
|
|
EBike "Throttle" / "Brake" Wiring Questions by oSPANNERo » Sun, 2022-02-27 16:07 |
3 |
by Jamesavery22 Sat, 2024-12-21 19:27 |
|
|
drill batteries in series with Flipsky 75100 by alexkid » Sat, 2022-05-14 15:41 |
2 |
by sergioma Sun, 2025-01-05 14:34 |
|
|
Difference between the current, duty cycle and PID speed control mode by tromes » Thu, 2020-06-11 07:51 |
8 |
by Onarb Kabr Wed, 2025-01-15 13:32 |
|
|
"Could not read Firmware version" when connecting via Bluetooth by ligi » Tue, 2020-11-17 07:03 |
14 |
by Gmcruz463 Fri, 2025-01-17 18:28 |
|
|
VESC PAS and ADC App - How does it work? by numbke » Fri, 2023-02-24 23:49 |
10 |
by anaka Sun, 2025-01-19 17:34 |
|
|
How to achieve synchronize position control by CAN between 2 VESCs by ztwsa007 » Sat, 2019-07-06 17:32 |
2 |
by mansi712 Tue, 2025-02-04 14:37 |
|
|
Overvoltage Error during setup by arranto12 » Mon, 2021-11-08 23:22 |
4 |
by electricfox Tue, 2025-02-04 19:28 |
|
|
Understanding Dual VESC (dual motors) setups by Cham » Mon, 2020-09-21 18:45 |
6 |
by hemmadroid Thu, 2025-03-06 06:34 |
|
|
Cant connect to Flipsky 75100 by Ed222 » Sun, 2022-03-20 00:31 |
5 |
by wimleo Wed, 2025-03-19 17:51 |
|
|
VESC settings for large scooter motor by trimen » Tue, 2020-07-14 22:15 |
10 |
by Juzy Tue, 2025-04-01 10:58 |
|
|
VESC crashes on Servo output by AutonomousDrifting » Fri, 2021-02-05 13:25 |
7 |
by dawgs Sat, 2025-04-19 12:40 |
|
|
What is the current state of mcus support? by il_piccione » Fri, 2025-04-25 09:47 |
0 |
by il_piccione Fri, 2025-04-25 09:47 |
|
|
VESC in-air startup failure by jschall » Sat, 2025-04-26 00:56 |
2 |
by jschall Sat, 2025-04-26 01:32 |
|
|
Flipsky 75200 Motor ruckelt und wird sehr schnell heiß by Oriessin » Sat, 2025-04-26 07:38 |
0 |
by Oriessin Sat, 2025-04-26 07:38 |
|
|
FlipSky 75/300 + Alien 80 KV noise/vibration under load by brendangillatt » Thu, 2021-01-07 01:19 |
13 |
by Thejesh Bollineni Wed, 2025-04-30 22:49 |
|
|
FSESC 75350 UNBALANCED_CURRENTS fault at higher loads by colmor » Thu, 2025-05-01 01:21 |
0 |
by colmor Thu, 2025-05-01 05:14 |
|
|
PID Speed Mode not limiting max ERPM by jordan73s » Sat, 2025-05-03 10:57 |
1 |
by colmor Thu, 2025-05-08 22:44 |
|
|
Vesc 4.12 USB Issues by puravida13 » Tue, 2025-05-06 18:45 |
1 |
by puravida13 Sat, 2025-05-10 01:53 |
Log in to post new content in the forum.
