You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
Motor jitters and skips poles, but only in one direction by L0laapk3 » Mon, 2022-09-19 21:32 |
7 |
by frank Wed, 2022-09-21 09:07 |
|
|
Flipsky 4.20 FOC settings Not Saving by erwinramos1010 » Mon, 2022-09-05 15:22 |
2 |
by wjpremerlani Sat, 2022-09-24 01:05 |
|
|
what is the best vesc For long-term sea observation by jhgjg » Thu, 2022-09-22 12:12 |
5 |
by frank Mon, 2022-09-26 15:44 |
|
|
SPINTEND UBOX 100v100a x2 or Flipsky 75100 100v100a x2 by DuckyTheDuck » Mon, 2022-09-26 12:07 |
3 |
by AngelKillR Wed, 2022-09-28 05:06 |
|
|
Serial Connection Lost with Vesc6.6 Firmware 5.2 and Vesc Tool 3.0 by Dan Slanker » Wed, 2021-04-28 16:56 |
9 |
by AngelKillR Wed, 2022-09-28 05:10 |
|
|
Back EMF or motor voltage back to the supply by bdesvaux » Tue, 2022-09-27 09:22 |
4 |
by bdesvaux Wed, 2022-09-28 15:52 |
|
|
VESC 6 75V, sensor voltage switch? by Alistair Goodman » Wed, 2022-09-28 15:53 |
2 |
by frank Wed, 2022-09-28 16:44 |
|
|
VESC packet fram-size by Yosh101 » Fri, 2022-09-30 15:34 |
0 |
by Yosh101 Fri, 2022-09-30 15:34 |
|
|
Motor Controller + Motor + Lecture by AlexSTM32 » Fri, 2022-09-30 19:29 |
1 |
by frank Sat, 2022-10-01 15:37 |
|
|
Vibrations under hard regen by gecko242 » Fri, 2022-10-07 15:03 |
1 |
by frank Fri, 2022-10-07 15:30 |
|
|
Trouble Detecting ABI Encoder on VESC6/75 by jonathansel » Fri, 2022-10-07 22:34 |
0 |
by jonathansel Fri, 2022-10-07 22:34 |
|
|
Overcurrent fault when braking by maxhertz » Fri, 2022-10-07 09:38 |
2 |
by maxhertz Sun, 2022-10-09 03:34 |
|
|
Suggestion for new forum area by Snabelost » Thu, 2022-10-06 23:55 |
2 |
by Snabelost Tue, 2022-10-11 18:30 |
|
|
Sudden hard acceleration at around 30 km/h. Help by kristofferbenjaminw » Tue, 2022-10-04 17:31 |
4 |
by Chris Barth Tue, 2022-10-11 20:05 |
|
|
UAV motor BLDC detection fails by Torbjorn » Wed, 2022-10-12 13:54 |
1 |
by frank Wed, 2022-10-12 17:04 |
|
|
Help needed in controlling multiple VESC boards (multiple motors) with VESC ROS (need to debug errors) by shreyas.srinivasan » Thu, 2022-10-13 08:13 |
0 |
by shreyas.srinivasan Thu, 2022-10-13 08:13 |
|
|
Slot car ESC? by adrianblakey » Thu, 2022-10-13 11:52 |
1 |
by frank Thu, 2022-10-13 14:49 |
|
|
Dual motor setup for Turnigy SK8 V2 60A x 2 3~12S Twin Motor Skateboard ESC? by fil02184 » Tue, 2022-10-18 04:07 |
0 |
by fil02184 Tue, 2022-10-18 16:00 |
|
|
Encoder connection by Herbie » Fri, 2019-05-31 15:12 |
11 |
by Dencio1976 Fri, 2022-10-21 13:46 |
|
|
Undervoltage Fault by gazlinux » Tue, 2022-02-08 02:26 |
3 |
by 67RS427 Fri, 2022-10-21 20:53 |
|
|
Looking for a technical co-founder for a VESC-Based Startup Project by pex » Fri, 2022-10-21 18:35 |
2 |
by pex Sat, 2022-10-22 01:37 |
|
|
GPIO Pins on VESC? by phils » Sat, 2022-10-22 17:58 |
1 |
by frank Sat, 2022-10-22 20:37 |
|
|
Inconsistant braking force when full brake starting to apply by Koxx3 » Sat, 2022-10-22 16:21 |
1 |
by Koxx3 Sun, 2022-10-23 13:22 |
|
|
Electric/ Gas Hybrid by kcswimrac » Wed, 2020-05-06 17:05 |
4 |
by drummerboy5408 Mon, 2022-10-24 05:43 |
|
|
Tuning prop loads with rapid erpm increase in duty cycle or speed control by mirage98 » Mon, 2022-09-26 01:51 |
1 |
by drummerboy5408 Mon, 2022-10-24 05:49 |
Log in to post new content in the forum.
