You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
VESC 6 for AUV applications by bc » Thu, 2018-02-22 15:57 |
5 |
by arvidb Fri, 2018-02-23 19:20 |
|
|
VESC6 and CableCam by wdaehn » Sun, 2018-02-18 16:52 |
14 |
by willyfan Thu, 2018-03-01 09:42 |
|
|
Difference between Brake Current, Full Brake etc by wdaehn » Wed, 2018-02-21 15:32 |
4 |
by rodread Sat, 2018-03-03 10:45 |
|
|
PID control with VESC by Hacker king » Mon, 2018-03-05 20:05 |
1 |
by Danny Bokma Tue, 2018-03-06 06:19 |
|
|
FOC Issue by Davideo » Mon, 2018-02-19 03:30 |
6 |
by yosoufe Thu, 2018-03-08 13:19 |
|
|
Website updates by benjamin » Fri, 2018-02-23 17:45 |
5 |
by benjamin Wed, 2018-03-14 10:46 |
|
|
UART GND to Battery (-), good idea ? by Pimousse » Sat, 2017-09-23 00:47 |
1 |
by Dillon Sat, 2018-03-17 05:56 |
|
|
how to stop regenerative braking option ? by tauhid.ann » Mon, 2018-03-12 18:40 |
5 |
by tauhid.ann Sat, 2018-03-17 21:21 |
|
|
Realtime Tachometer readings over UART by Davideo » Thu, 2017-12-07 00:10 |
1 |
by azobe Mon, 2018-03-19 04:28 |
|
|
Noise with Hall sensor at high speed by yosoufe » Thu, 2018-03-08 12:34 |
9 |
by yosoufe Tue, 2018-03-20 09:30 |
|
|
Which encoders are supported? by raess » Thu, 2018-03-22 23:38 |
2 |
by raess Fri, 2018-03-23 22:58 |
|
|
Can motor parameters be detected with shaft load? by powerlabor001 » Thu, 2018-03-15 13:24 |
4 |
by powerlabor001 Sat, 2018-03-24 03:07 |
|
|
can not start motor with high duty by qdxiatao » Sat, 2018-03-24 03:58 |
0 |
by qdxiatao Sat, 2018-03-24 03:58 |
|
|
vesc6 help me learn by badger1666 » Sat, 2018-03-31 09:05 |
2 |
by badger1666 Mon, 2018-04-02 20:15 |
|
|
Timeout Brake Current [Fail Save] by Cuprani » Mon, 2018-04-02 00:03 |
2 |
by Cuprani Tue, 2018-04-03 12:28 |
|
|
acceleration speed and temp noise by badger1666 » Wed, 2018-04-04 20:18 |
5 |
by badger1666 Fri, 2018-04-06 20:13 |
|
|
Potentiometer control by khadra.m123 » Thu, 2018-04-05 08:51 |
3 |
by slapshot136 Sun, 2018-04-08 00:07 |
|
|
Can't find Configurable FOC current filter in VESC TOOL by e-biker » Sun, 2018-04-08 12:18 |
2 |
by e-biker Sun, 2018-04-08 12:55 |
|
|
Motor temperature increase by e-biker » Sun, 2018-04-08 20:17 |
4 |
by e-biker Mon, 2018-04-09 14:44 |
|
|
Hall sensor filter on VESC flier board by raess » Tue, 2018-03-27 21:00 |
17 |
by raess Wed, 2018-04-11 13:43 |
|
|
Extending current shunt amplifier voltage by TechAUmNu » Wed, 2018-04-11 00:43 |
2 |
by Roger Wolff Tue, 2018-04-17 08:56 |
|
|
can't reach the maximum speed by kingpon » Sat, 2017-10-28 04:55 |
3 |
by elektrinis Tue, 2018-04-17 21:50 |
|
|
Firmware update thru UART? by cromoly » Tue, 2018-04-17 01:19 |
4 |
by cromoly Fri, 2018-04-20 19:22 |
|
|
Brakes completely repeatedly failing at high temperature by Paul15578 » Mon, 2018-03-26 13:06 |
10 |
by Paul15578 Sun, 2018-04-22 14:16 |
|
|
ERPM settings restrict carving speed on outer wheel. Poor user experience. by Paul15578 » Fri, 2018-01-12 02:28 |
9 |
by Ackmaniac Tue, 2018-04-24 13:47 |
Log in to post new content in the forum.
