You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
VESC 6: frequent direction change application problem by cromoly » Thu, 2019-05-02 01:45 |
0 |
by cromoly Thu, 2019-05-02 01:45 |
|
|
VESC API? by ufechner » Sun, 2018-03-11 14:05 |
3 |
by vimi94 Fri, 2019-05-03 18:45 |
|
|
High rpm issue kde3520xf by magnus.w » Fri, 2019-04-26 12:46 |
1 |
by magnus.w Sat, 2019-05-04 12:33 |
|
|
RPM Control Problems by MrMonk3y » Mon, 2019-05-06 22:54 |
0 |
by MrMonk3y Mon, 2019-05-06 22:54 |
|
|
Connecting VESC to XAVIER by MrMonk3y » Wed, 2019-05-01 09:53 |
1 |
by MrMonk3y Wed, 2019-05-08 13:34 |
|
|
Using Motor hall sensors as the encoder by Russ g » Wed, 2019-05-08 16:01 |
0 |
by Russ g Wed, 2019-05-08 16:01 |
|
|
VESC 75/300, TP 100 inrunner 10KW by Markula » Thu, 2019-05-02 13:58 |
5 |
by Markula Wed, 2019-05-08 18:59 |
|
|
100k NTC by CTSchorsch » Tue, 2019-05-07 17:18 |
3 |
by Roger Wolff Sat, 2019-05-11 13:00 |
|
|
E-Bike Throttle connect with Regenerative Braking by E-Toxx » Sat, 2017-09-09 09:38 |
4 |
by Jacki Villis Thu, 2019-05-16 14:43 |
|
|
DC-Link Capacitor Selection by rushi95 » Sat, 2019-05-18 12:15 |
1 |
by hexakopter Sat, 2019-05-18 12:39 |
|
|
FOC Detection works but BLDC detection fails by gv260ea » Sun, 2019-05-19 04:15 |
0 |
by gv260ea Sun, 2019-05-19 04:15 |
|
|
Reading tachometer over can bus by kimpet » Sun, 2019-05-12 22:24 |
5 |
by benjamin Sun, 2019-05-19 14:58 |
|
|
Strange behaviour when controlling RPM by MrMonk3y » Wed, 2019-05-08 14:29 |
1 |
by cnd Mon, 2019-05-27 08:41 |
|
|
half speed on FOC vs BLDC by ever.summer » Tue, 2019-05-28 00:04 |
4 |
by ever.summer Tue, 2019-05-28 04:34 |
|
|
Arduino UART communication HW4.10 FW3.56 by joseguerra » Wed, 2019-05-22 13:01 |
1 |
by Pimousse Thu, 2019-05-30 17:23 |
|
|
What is a common motor efficiency? I'm at 72% by ever.summer » Tue, 2019-05-28 05:02 |
5 |
by Roger Wolff Sun, 2019-06-02 10:19 |
|
|
VESC at very low speeds by LudoJ » Wed, 2019-05-15 16:09 |
1 |
by Roger Wolff Sun, 2019-06-02 10:25 |
|
|
Brake Current Command Adjustments by josh » Fri, 2019-05-17 21:37 |
2 |
by josh Wed, 2019-06-05 17:14 |
|
|
Step/Dir signals by wall0069 » Sun, 2019-06-09 16:06 |
0 |
by wall0069 Sun, 2019-06-09 16:06 |
|
|
Sync loss when switching from HALL to sensorless by blezalex » Fri, 2019-05-24 19:00 |
1 |
by blezalex Mon, 2019-06-10 23:26 |
|
|
VESC 6 FOC wizard and current limitations. by Bor Zabric » Mon, 2019-06-10 21:12 |
1 |
by TechAUmNu Wed, 2019-06-12 14:42 |
|
|
Recommended way to implement CAN-bus communication using a Linux based controller by toma » Tue, 2019-06-11 08:32 |
8 |
by toma Thu, 2019-06-13 07:43 |
|
|
Motor refuses to spin after Wizard, VESC 6.6 by Wisdomwagon » Thu, 2019-06-13 16:20 |
1 |
by Wisdomwagon Thu, 2019-06-13 18:54 |
|
|
Difference between maximum current values by Rico » Fri, 2019-06-14 16:06 |
1 |
by frank Sat, 2019-06-15 12:21 |
|
|
Regenerative braking question and vesc input question by asaf123098 » Sat, 2019-06-15 09:55 |
2 |
by asaf123098 Sun, 2019-06-16 00:23 |
Log in to post new content in the forum.
