You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Basic VESC troubleshooting (postmortem?) by N_COUNTER » Tue, 2023-03-14 10:58 |
0 |
by N_COUNTER Tue, 2023-03-14 11:01 |
|
|
IPM parameter adjust by rbargallo » Sun, 2021-05-23 22:43 |
0 |
by rbargallo Sun, 2021-05-23 22:43 |
|
|
Drive frequency and command rate question by jediengineer » Sun, 2023-03-19 19:07 |
0 |
by jediengineer Sun, 2023-03-19 19:08 |
|
|
Battlebot Weapon : Trouble spinning up by satacoy » Thu, 2019-04-04 07:29 |
0 |
by satacoy Thu, 2019-04-04 07:29 |
|
|
Issues running a gimbal motor by ksau » Thu, 2021-03-11 16:44 |
0 |
by ksau Thu, 2021-03-11 16:44 |
|
|
Speed control issues w. hub motors by akerblad » Sun, 2019-04-07 17:22 |
0 |
by akerblad Sun, 2019-04-07 17:22 |
|
|
3Shul 700A reporting negative current spikes by reobaird » Sat, 2023-03-25 03:22 |
0 |
by reobaird Mon, 2023-03-27 09:34 |
|
|
Power by kuba12 » Sun, 2021-03-14 20:46 |
0 |
by kuba12 Mon, 2021-03-15 15:10 |
|
|
current control mode with duty cycle limit based on throttle by devin » Thu, 2020-01-16 05:45 |
0 |
by devin Thu, 2020-01-16 05:49 |
|
|
Disable wrong FET temperature sensors by Flo98 » Sat, 2024-10-19 17:49 |
0 |
by Flo98 Sat, 2024-10-19 17:54 |
|
|
Changing the Control Mode Using PPM by Nickicook4noswag » Mon, 2024-07-08 03:27 |
0 |
by Nickicook4noswag Mon, 2024-07-08 03:27 |
|
|
Additional Status Messages by louisgcr » Tue, 2021-12-21 08:04 |
0 |
by louisgcr Tue, 2021-12-21 08:04 |
|
|
Motor draws current (up to 120 A), but doesn't turn by Heimfried » Sun, 2020-03-01 22:21 |
0 |
by Heimfried Sun, 2020-03-01 22:21 |
|
|
How to setup my VESC with AD2S1205 by Vlahosthomas » Tue, 2024-10-22 10:33 |
0 |
by Vlahosthomas Tue, 2024-10-22 10:36 |
|
|
Opinion on Dual motor and FW on One by theblash » Thu, 2024-07-11 11:00 |
0 |
by theblash Thu, 2024-07-11 11:00 |
|
|
Parsing PPM data from CAN Bus by walleywalker » Sun, 2021-12-26 23:57 |
0 |
by walleywalker Sun, 2021-12-26 23:57 |
|
|
Vesc_tool running error by kwlimm » Sun, 2020-01-19 10:01 |
0 |
by kwlimm Sun, 2020-01-19 10:01 |
|
|
Closed Loop Control Not Working by Ayden1717 » Sun, 2024-07-14 19:20 |
0 |
by Ayden1717 Sun, 2024-07-14 19:20 |
|
|
Limiting Down hill speed by dbau » Sat, 2022-01-29 06:54 |
0 |
by dbau Sat, 2022-01-29 09:19 |
|
|
Arduino- UART Library Question... by arranto12 » Sun, 2022-01-02 09:57 |
0 |
by arranto12 Sun, 2022-01-02 09:57 |
|
|
Vesc 75/300 max current by a727dd » Wed, 2020-03-04 04:34 |
0 |
by a727dd Wed, 2020-03-04 04:34 |
|
|
Using the VESC6MK VI HP braking current by uropthing » Thu, 2024-07-25 13:40 |
0 |
by uropthing Thu, 2024-07-25 13:40 |
|
|
VESC apps by bosko » Thu, 2020-01-23 18:28 |
0 |
by bosko Thu, 2020-01-23 18:28 |
|
|
HFI and braking by aethyr » Thu, 2020-03-19 21:01 |
0 |
by aethyr Thu, 2020-03-19 21:01 |
|
|
VESC with Ey4 and special function by MachWas » Mon, 2024-08-12 02:34 |
0 |
by MachWas Mon, 2024-08-12 02:34 |
Log in to post new content in the forum.
