You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
VESC ADC1 throttle configuration like an EV-Rekuperation by sega » Wed, 2024-06-12 17:48 |
0 |
by sega Wed, 2024-06-12 17:48 |
|
|
OneWheel Pint Torque by VirtualGrid » Fri, 2024-06-14 03:28 |
0 |
by VirtualGrid Fri, 2024-06-14 03:28 |
|
|
Delayed start for slave motor by rsknudsen-dk » Mon, 2020-04-06 10:06 |
0 |
by rsknudsen-dk Mon, 2020-04-06 10:06 |
|
|
Current mismatch between power supply and vesc tool by mansi712 » Tue, 2024-09-24 13:02 |
0 |
by mansi712 Tue, 2024-09-24 18:08 |
|
|
PPM Position over CAN bus? by walleywalker » Thu, 2021-12-02 18:47 |
0 |
by walleywalker Thu, 2021-12-02 18:47 |
|
|
rpm fail in FOC sensor mode by mansi712 » Thu, 2024-09-26 19:51 |
0 |
by mansi712 Thu, 2024-09-26 19:51 |
|
|
How can I get current data from VESC to stm32f446re by hyedo » Sun, 2022-01-23 19:38 |
0 |
by hyedo Sun, 2022-01-23 19:38 |
|
|
Welding with the VESC by doomy1986 » Mon, 2020-04-13 14:38 |
0 |
by doomy1986 Mon, 2020-04-13 14:38 |
|
|
error message binding loop detected for property ! wtf by georg65 » Sat, 2024-09-28 08:49 |
0 |
by georg65 Tue, 2024-10-01 03:04 |
|
|
If the PPM line is completely destroyed, is it possible to program another one? by Nickicook4noswag » Tue, 2024-06-25 05:57 |
0 |
by Nickicook4noswag Tue, 2024-06-25 05:57 |
|
|
How turn on /off Vesc MKS 75200 by baybradyr » Mon, 2024-07-01 22:10 |
0 |
by baybradyr Mon, 2024-07-01 22:10 |
|
|
current control mode with duty cycle limit based on throttle by devin » Thu, 2020-01-16 05:45 |
0 |
by devin Thu, 2020-01-16 05:49 |
|
|
Disable wrong FET temperature sensors by Flo98 » Sat, 2024-10-19 17:49 |
0 |
by Flo98 Sat, 2024-10-19 17:54 |
|
|
Changing the Control Mode Using PPM by Nickicook4noswag » Mon, 2024-07-08 03:27 |
0 |
by Nickicook4noswag Mon, 2024-07-08 03:27 |
|
|
Additional Status Messages by louisgcr » Tue, 2021-12-21 08:04 |
0 |
by louisgcr Tue, 2021-12-21 08:04 |
|
|
Motor draws current (up to 120 A), but doesn't turn by Heimfried » Sun, 2020-03-01 22:21 |
0 |
by Heimfried Sun, 2020-03-01 22:21 |
|
|
How to setup my VESC with AD2S1205 by Vlahosthomas » Tue, 2024-10-22 10:33 |
0 |
by Vlahosthomas Tue, 2024-10-22 10:36 |
|
|
Opinion on Dual motor and FW on One by theblash » Thu, 2024-07-11 11:00 |
0 |
by theblash Thu, 2024-07-11 11:00 |
|
|
Parsing PPM data from CAN Bus by walleywalker » Sun, 2021-12-26 23:57 |
0 |
by walleywalker Sun, 2021-12-26 23:57 |
|
|
Porting VESC to STML4 by Vince_1618 » Fri, 2022-10-28 14:01 |
0 |
by Vince_1618 Fri, 2022-10-28 14:01 |
|
|
HFI optimisation with increase in switching frequency by rainebk@bigpond... » Tue, 2022-09-13 06:53 |
0 |
by rainebk@bigpond... Tue, 2022-09-13 06:53 |
|
|
VESC Wand shows INF and 100% Batt by BLKFLD » Sat, 2020-09-26 04:48 |
0 |
by BLKFLD Sat, 2020-09-26 04:48 |
|
|
Tuning process? by wingborne » Tue, 2020-09-29 00:09 |
0 |
by wingborne Tue, 2020-09-29 21:39 |
|
|
VESC Software Understanding by shubhamt » Wed, 2018-08-22 15:40 |
0 |
by shubhamt Wed, 2018-08-22 15:40 |
|
|
Bricked my VESC six what now? by atat » Sun, 2018-05-20 13:07 |
0 |
by atat Sun, 2018-05-20 14:28 |
Log in to post new content in the forum.
