You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Servo Mode / ODrive on VESC by JulianT » Tue, 2020-02-04 09:19 |
0 |
by JulianT Tue, 2020-02-04 09:19 |
|
|
CAN bus rate, Flipsky Mini FSESC6.7 by christian.lees » Tue, 2022-01-18 22:57 |
0 |
by christian.lees Tue, 2022-01-18 22:57 |
|
|
Large robot servo controller with VESC, how to set up position control by kisdia » Thu, 2024-09-19 17:47 |
0 |
by kisdia Thu, 2024-09-19 17:47 |
|
|
Can't Update Firmware by indianboy42 » Mon, 2024-06-17 08:54 |
0 |
by indianboy42 Mon, 2024-06-17 08:54 |
|
|
vesc setup 42V 10A e-bike accu to build in a E-skatboard by olaf2273 » Fri, 2020-04-10 12:33 |
0 |
by olaf2273 Mon, 2020-04-27 15:34 |
|
|
Firmware V4.00 field oriented control motor jerk but wont spin by jordanlow » Thu, 2020-02-13 14:41 |
0 |
by jordanlow Thu, 2020-02-13 14:41 |
|
|
Maximum Motor RPM will not reached by Skyver » Sun, 2022-01-23 10:53 |
0 |
by Skyver Sun, 2022-01-23 10:53 |
|
|
Running PID position Control with FOC sensorless by talabo » Fri, 2021-12-03 17:21 |
0 |
by talabo Fri, 2021-12-03 17:21 |
|
|
Connecting AMT203 to Flipsky 4.20 ESC by kgeo0003 » Mon, 2022-01-24 06:44 |
0 |
by kgeo0003 Mon, 2022-01-24 09:00 |
|
|
Autonomous RC car with Focbox suddenly stops by Autocar » Mon, 2021-12-06 06:55 |
0 |
by Autocar Mon, 2021-12-06 06:55 |
|
|
Incorrect Batt Current Readings in FOC but not in BLDC by vadicus » Tue, 2020-02-25 20:06 |
0 |
by vadicus Tue, 2020-02-25 20:09 |
|
|
Read telemetry data from USB port by mlsc » Sun, 2024-10-06 22:01 |
0 |
by mlsc Sun, 2024-10-06 22:01 |
|
|
Setting RPM over UART by klay2000 » Sat, 2024-06-29 01:27 |
0 |
by klay2000 Sat, 2024-06-29 01:28 |
|
|
Intens and violent stuttering at low RPM - 75200 and QS205 by mdethmers » Mon, 2026-09-28 13:43 |
0 |
by mdethmers Mon, 2026-09-28 13:43 |
|
|
Encoder maximum PPR/CPR by Michelle90 » Mon, 2022-09-05 22:16 |
0 |
by Michelle90 Mon, 2022-09-05 22:16 |
|
|
How to use an IMU and a PPM remote parallel by Gos1 » Tue, 2022-10-25 15:28 |
0 |
by Gos1 Wed, 2022-10-26 10:57 |
|
|
Maximize startup torque by arosenthal » Sat, 2020-11-14 14:16 |
0 |
by arosenthal Sat, 2020-11-14 14:17 |
|
|
Cannot connect to VESC via USB or SWD by hagis » Wed, 2020-09-23 17:21 |
0 |
by hagis Wed, 2020-09-23 17:21 |
|
|
Issue with VESC I/O on donkey car by baluja » Fri, 2022-10-28 02:56 |
0 |
by baluja Fri, 2022-10-28 02:56 |
|
|
Inquiry about Incremental and Absolute Encoders in VESC for Robotics by sivanhere » Fri, 2022-10-28 21:02 |
0 |
by sivanhere Fri, 2022-10-28 21:02 |
|
|
Voltage spikes on BEMF scope by Sgw32 » Wed, 2020-11-18 16:03 |
0 |
by Sgw32 Wed, 2020-11-18 16:06 |
|
|
What do i need? by Robert Thomas » Fri, 2022-09-16 21:39 |
0 |
by Robert Thomas Fri, 2022-09-16 22:12 |
|
|
Angle offset detection by Gas_Sn4ke » Mon, 2019-01-21 07:09 |
0 |
by Gas_Sn4ke Mon, 2019-01-21 07:09 |
|
|
Separate Deadband for ADC2? by striderkent » Wed, 2019-01-23 16:31 |
0 |
by striderkent Wed, 2019-01-23 16:31 |
|
|
Does PLL measure the REAL motor speed by wyk » Mon, 2020-11-23 08:34 |
0 |
by wyk Mon, 2020-11-23 08:34 |
Log in to post new content in the forum.
