You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Battery percentage mapping by Sharkboy » Mon, 2024-05-06 22:55 |
0 |
by Sharkboy Mon, 2024-05-06 22:55 |
|
|
Runtime motor control with CAN by Davidepolpi91 » Fri, 2024-03-15 15:12 |
0 |
by Davidepolpi91 Fri, 2024-03-15 15:12 |
|
|
Flysky FESC 6.7 to disable 5V by AryehChen » Wed, 2024-05-15 18:44 |
0 |
by AryehChen Wed, 2024-05-15 18:46 |
|
|
noob with so many setup/wiring questions...... by flez1966 » Sun, 2024-03-17 20:17 |
0 |
by flez1966 Sun, 2024-03-17 20:17 |
|
|
Unofficial VESC Discord server by kubark42 » Tue, 2021-11-16 16:07 |
0 |
by kubark42 Fri, 2021-11-19 03:12 |
|
|
Reading COMM packets through CAN. by 1423rj » Mon, 2024-05-20 08:22 |
0 |
by 1423rj Mon, 2024-05-20 08:23 |
|
|
Reverse indicator by bmblank » Wed, 2024-03-20 20:41 |
0 |
by bmblank Wed, 2024-03-20 20:41 |
|
|
DRV8302 Gate Pin output waveform is abnormal by yandongyu1998 » Fri, 2019-12-13 07:21 |
0 |
by yandongyu1998 Fri, 2019-12-13 07:21 |
|
|
Low torque at 0 RPM by ivan_osyotr » Sat, 2024-06-01 18:37 |
0 |
by ivan_osyotr Sat, 2024-06-01 18:37 |
|
|
VESC 4.12 Current limit question by jamesk18@vt.edu » Tue, 2024-03-26 18:30 |
0 |
by jamesk18@vt.edu Tue, 2024-03-26 18:30 |
|
|
The rpm control is not working properly by ptss37 » Wed, 2021-11-24 03:30 |
0 |
by ptss37 Wed, 2021-11-24 03:44 |
|
|
Upgrading to higher voltage setup by JPK2 » Wed, 2024-06-05 22:11 |
0 |
by JPK2 Wed, 2024-06-05 22:11 |
|
|
Any issues with the DRV8323? by shaman » Thu, 2019-10-24 21:50 |
0 |
by shaman Thu, 2019-10-24 21:50 |
|
|
VESC 6 Mk IV Phase 1 Current Double Others by bayetan » Mon, 2024-01-29 16:13 |
0 |
by bayetan Mon, 2024-01-29 16:13 |
|
|
Issue connecting to Flipsky VESC with mobile app (Firmware 6.0.6) by Gabifat » Mon, 2025-12-15 08:35 |
0 |
by Gabifat Mon, 2025-12-15 08:35 |
|
|
Sleep mode? by pcace » Wed, 2025-07-30 06:48 |
0 |
by pcace Wed, 2025-07-30 06:48 |
|
|
How to increase the +/-165A rms current limit to 250A+ rms (350-400A peak) by ev_motors » Sat, 2018-04-28 10:18 |
0 |
by ev_motors Sat, 2018-04-28 10:18 |
|
|
BRAND NEW R SPEC DUAL 6355 (4.12 VESC) SET UP ISSUES by rodriguezjoe1@b... » Mon, 2020-09-07 17:50 |
0 |
by rodriguezjoe1@b... Mon, 2020-09-07 17:50 |
|
|
Making master and slave motors communicate both ways by Sis7 » Tue, 2020-07-21 05:58 |
0 |
by Sis7 Tue, 2020-07-21 05:58 |
|
|
Question about duty cycle control Vs current control mode by hazzahodgson » Wed, 2026-01-21 08:34 |
0 |
by hazzahodgson Wed, 2026-01-21 08:34 |
|
|
flatten the curve / powerband by TONY61 » Sun, 2025-08-10 15:26 |
0 |
by TONY61 Sun, 2025-08-10 15:26 |
|
|
Best way to run a hoverboard motor that has an AB encoder and Hall sensors, but no index? by PaulMakesThings » Thu, 2022-06-23 23:43 |
0 |
by PaulMakesThings Thu, 2022-06-23 23:43 |
|
|
VESC 60 75 IMU by Alistair Goodman » Thu, 2025-08-14 18:23 |
0 |
by Alistair Goodman Thu, 2025-08-14 18:23 |
|
|
GT2 Remote to Vesc connection issue by tom.embke » Tue, 2018-05-01 14:41 |
0 |
by tom.embke Tue, 2018-05-01 14:41 |
|
|
resistance and inductance value changes when each measurement by alexshen2012 » Fri, 2022-07-01 05:42 |
0 |
by alexshen2012 Fri, 2022-07-01 05:42 |
Log in to post new content in the forum.
