You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Help Please 🥺 by Jou2023 » Sun, 2023-05-28 17:58 |
0 |
by Jou2023 Sun, 2023-05-28 17:58 |
|
|
Configuration of underwater thruster by UnderwaterMotors » Fri, 2023-03-24 18:10 |
0 |
by UnderwaterMotors Fri, 2023-03-24 18:10 |
|
|
Trying to read and set MCCONF by Jamie42 » Tue, 2020-03-24 19:47 |
0 |
by Jamie42 Tue, 2020-03-24 19:47 |
|
|
Vesc 75100 by Matteo Christian » Wed, 2023-05-31 13:32 |
0 |
by Matteo Christian Fri, 2023-06-09 12:08 |
|
|
4 fried vesc's Australia by adamclarke1985 » Tue, 2020-03-31 20:48 |
0 |
by adamclarke1985 Tue, 2020-03-31 21:24 |
|
|
VESC appears to loose sync when increasing throttle by srinath » Sun, 2023-06-04 04:11 |
0 |
by srinath Sun, 2023-06-04 04:11 |
|
|
No load FOC stops when full FWD throttle. by toboli » Mon, 2023-06-05 18:41 |
0 |
by toboli Mon, 2023-06-05 18:41 |
|
|
Servo Mode / ODrive on VESC by JulianT » Tue, 2020-02-04 09:19 |
0 |
by JulianT Tue, 2020-02-04 09:19 |
|
|
RPM and torque control modes by srinath » Fri, 2023-06-16 10:52 |
0 |
by srinath Fri, 2023-06-16 10:54 |
|
|
Error code 6 by PatWhite32 » Mon, 2023-06-19 23:15 |
0 |
by PatWhite32 Mon, 2023-06-19 23:15 |
|
|
Motor runs only at constant speed (with VESC 100V200A and Flipsky VX3). by Tom65 » Wed, 2023-04-12 16:28 |
0 |
by Tom65 Wed, 2023-04-12 16:28 |
|
|
Problems with UART communication via Arduino UNO by Michael Hamm » Fri, 2022-02-04 13:29 |
0 |
by Michael Hamm Fri, 2022-02-04 13:29 |
|
|
Flipsky Mini Dual FSESC4.20+voyager remote+tankmode by allan_overbye » Fri, 2024-11-08 14:13 |
0 |
by allan_overbye Fri, 2024-11-08 14:13 |
|
|
Help with translating/converting hall sensor values from BLDC to FOC by theviith » Thu, 2018-10-11 09:47 |
0 |
by theviith Thu, 2018-10-11 09:47 |
|
|
CAN eRPM report by alxsfrm » Mon, 2022-02-07 11:01 |
0 |
by alxsfrm Mon, 2022-02-07 11:01 |
|
|
Motor won't hold constant speed by Groundspeed100 » Thu, 2024-11-14 05:33 |
0 |
by Groundspeed100 Thu, 2024-11-14 05:33 |
|
|
Payment by Paypal. by ThierryGTLTS » Wed, 2017-09-06 14:38 |
0 |
by ThierryGTLTS Wed, 2017-09-06 17:50 |
|
|
Use IMU for keeping direction by arnolde » Mon, 2024-11-25 11:12 |
0 |
by arnolde Mon, 2024-11-25 11:19 |
|
|
Storing VESC Tool data for later analysis by AidanNowa » Wed, 2024-06-12 15:57 |
0 |
by AidanNowa Wed, 2024-06-12 15:57 |
|
|
Maximize startup torque by arosenthal » Sat, 2020-11-14 14:16 |
0 |
by arosenthal Sat, 2020-11-14 14:17 |
|
|
Cannot connect to VESC via USB or SWD by hagis » Wed, 2020-09-23 17:21 |
0 |
by hagis Wed, 2020-09-23 17:21 |
|
|
CAN bus rate, Flipsky Mini FSESC6.7 by christian.lees » Tue, 2022-01-18 22:57 |
0 |
by christian.lees Tue, 2022-01-18 22:57 |
|
|
Large robot servo controller with VESC, how to set up position control by kisdia » Thu, 2024-09-19 17:47 |
0 |
by kisdia Thu, 2024-09-19 17:47 |
|
|
Can't Update Firmware by indianboy42 » Mon, 2024-06-17 08:54 |
0 |
by indianboy42 Mon, 2024-06-17 08:54 |
|
|
Voltage spikes on BEMF scope by Sgw32 » Wed, 2020-11-18 16:03 |
0 |
by Sgw32 Wed, 2020-11-18 16:06 |
Log in to post new content in the forum.
