You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Read telemetry data from USB port by mlsc » Sun, 2024-10-06 22:01 |
0 |
by mlsc Sun, 2024-10-06 22:01 |
|
|
Setting RPM over UART by klay2000 » Sat, 2024-06-29 01:27 |
0 |
by klay2000 Sat, 2024-06-29 01:28 |
|
|
Current control performance & best way to tune Kp and Ki by jinwonchung » Thu, 2024-10-17 15:52 |
0 |
by jinwonchung Thu, 2024-10-17 15:53 |
|
|
custom firmware by vufmihai » Thu, 2020-01-16 09:06 |
0 |
by vufmihai Thu, 2020-01-16 09:06 |
|
|
Do All Vescs Suck? by Zeebybaby » Sun, 2024-10-20 20:33 |
0 |
by Zeebybaby Sun, 2024-10-20 20:33 |
|
|
Variable regen braking by Gsorter » Thu, 2024-07-11 00:04 |
0 |
by Gsorter Thu, 2024-07-11 00:04 |
|
|
Comms plug and leads by craig w » Fri, 2021-12-24 00:25 |
0 |
by craig w Fri, 2021-12-24 00:25 |
|
|
PAS only one signal + BLE by sifourquier » Fri, 2021-12-31 19:08 |
0 |
by sifourquier Fri, 2021-12-31 19:08 |
|
|
No sensers by Phill Dixon » Thu, 2024-10-24 18:58 |
0 |
by Phill Dixon Thu, 2024-10-24 18:58 |
|
|
General help by jskessel » Tue, 2024-07-16 20:09 |
0 |
by jskessel Tue, 2024-07-16 20:09 |
|
|
VESC 6.6 vs. MK5 vs. MK6 by jejaj25773 » Sat, 2024-07-27 02:37 |
0 |
by jejaj25773 Sat, 2024-07-27 02:37 |
|
|
Help with FOC/PID parameter by CTSchorsch » Thu, 2020-01-23 21:57 |
0 |
by CTSchorsch Thu, 2020-01-23 21:57 |
|
|
Problems with UART communication via Arduino UNO by Michael Hamm » Fri, 2022-02-04 13:29 |
0 |
by Michael Hamm Fri, 2022-02-04 13:29 |
|
|
Flipsky Mini Dual FSESC4.20+voyager remote+tankmode by allan_overbye » Fri, 2024-11-08 14:13 |
0 |
by allan_overbye Fri, 2024-11-08 14:13 |
|
|
CAN eRPM report by alxsfrm » Mon, 2022-02-07 11:01 |
0 |
by alxsfrm Mon, 2022-02-07 11:01 |
|
|
Trying to read and set MCCONF by Jamie42 » Tue, 2020-03-24 19:47 |
0 |
by Jamie42 Tue, 2020-03-24 19:47 |
|
|
Motor won't hold constant speed by Groundspeed100 » Thu, 2024-11-14 05:33 |
0 |
by Groundspeed100 Thu, 2024-11-14 05:33 |
|
|
4 fried vesc's Australia by adamclarke1985 » Tue, 2020-03-31 20:48 |
0 |
by adamclarke1985 Tue, 2020-03-31 21:24 |
|
|
Use IMU for keeping direction by arnolde » Mon, 2024-11-25 11:12 |
0 |
by arnolde Mon, 2024-11-25 11:19 |
|
|
Storing VESC Tool data for later analysis by AidanNowa » Wed, 2024-06-12 15:57 |
0 |
by AidanNowa Wed, 2024-06-12 15:57 |
|
|
Servo Mode / ODrive on VESC by JulianT » Tue, 2020-02-04 09:19 |
0 |
by JulianT Tue, 2020-02-04 09:19 |
|
|
CAN bus rate, Flipsky Mini FSESC6.7 by christian.lees » Tue, 2022-01-18 22:57 |
0 |
by christian.lees Tue, 2022-01-18 22:57 |
|
|
Large robot servo controller with VESC, how to set up position control by kisdia » Thu, 2024-09-19 17:47 |
0 |
by kisdia Thu, 2024-09-19 17:47 |
|
|
Can't Update Firmware by indianboy42 » Mon, 2024-06-17 08:54 |
0 |
by indianboy42 Mon, 2024-06-17 08:54 |
|
|
vesc setup 42V 10A e-bike accu to build in a E-skatboard by olaf2273 » Fri, 2020-04-10 12:33 |
0 |
by olaf2273 Mon, 2020-04-27 15:34 |
Log in to post new content in the forum.
