You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
RPM and torque control modes by srinath » Fri, 2023-06-16 10:52 |
0 |
by srinath Fri, 2023-06-16 10:54 |
|
|
Flipsky6.6 usb not detected This topic has been moved to "Third Party Hardware" (View topic) |
|||
|
Error code 6 by PatWhite32 » Mon, 2023-06-19 23:15 |
0 |
by PatWhite32 Mon, 2023-06-19 23:15 |
|
|
Motor runs only at constant speed (with VESC 100V200A and Flipsky VX3). by Tom65 » Wed, 2023-04-12 16:28 |
0 |
by Tom65 Wed, 2023-04-12 16:28 |
|
|
current measurements crazy high after replacing DRV8301 with DRV8302, it throws a FAULT_CODE_ABS_OVER_CURRENT by idkanythinggoes » Thu, 2021-03-18 04:34 |
0 |
by idkanythinggoes Thu, 2021-03-18 04:34 |
|
|
Help with FOC/PID parameter by CTSchorsch » Thu, 2020-01-23 21:57 |
0 |
by CTSchorsch Thu, 2020-01-23 21:57 |
|
|
Problems with UART communication via Arduino UNO by Michael Hamm » Fri, 2022-02-04 13:29 |
0 |
by Michael Hamm Fri, 2022-02-04 13:29 |
|
|
Flipsky Mini Dual FSESC4.20+voyager remote+tankmode by allan_overbye » Fri, 2024-11-08 14:13 |
0 |
by allan_overbye Fri, 2024-11-08 14:13 |
|
|
CAN eRPM report by alxsfrm » Mon, 2022-02-07 11:01 |
0 |
by alxsfrm Mon, 2022-02-07 11:01 |
|
|
Trying to read and set MCCONF by Jamie42 » Tue, 2020-03-24 19:47 |
0 |
by Jamie42 Tue, 2020-03-24 19:47 |
|
|
Motor won't hold constant speed by Groundspeed100 » Thu, 2024-11-14 05:33 |
0 |
by Groundspeed100 Thu, 2024-11-14 05:33 |
|
|
4 fried vesc's Australia by adamclarke1985 » Tue, 2020-03-31 20:48 |
0 |
by adamclarke1985 Tue, 2020-03-31 21:24 |
|
|
Use IMU for keeping direction by arnolde » Mon, 2024-11-25 11:12 |
0 |
by arnolde Mon, 2024-11-25 11:19 |
|
|
Storing VESC Tool data for later analysis by AidanNowa » Wed, 2024-06-12 15:57 |
0 |
by AidanNowa Wed, 2024-06-12 15:57 |
|
|
Servo Mode / ODrive on VESC by JulianT » Tue, 2020-02-04 09:19 |
0 |
by JulianT Tue, 2020-02-04 09:19 |
|
|
CAN bus rate, Flipsky Mini FSESC6.7 by christian.lees » Tue, 2022-01-18 22:57 |
0 |
by christian.lees Tue, 2022-01-18 22:57 |
|
|
Large robot servo controller with VESC, how to set up position control by kisdia » Thu, 2024-09-19 17:47 |
0 |
by kisdia Thu, 2024-09-19 17:47 |
|
|
Can't Update Firmware by indianboy42 » Mon, 2024-06-17 08:54 |
0 |
by indianboy42 Mon, 2024-06-17 08:54 |
|
|
vesc setup 42V 10A e-bike accu to build in a E-skatboard by olaf2273 » Fri, 2020-04-10 12:33 |
0 |
by olaf2273 Mon, 2020-04-27 15:34 |
|
|
Firmware V4.00 field oriented control motor jerk but wont spin by jordanlow » Thu, 2020-02-13 14:41 |
0 |
by jordanlow Thu, 2020-02-13 14:41 |
|
|
Maximum Motor RPM will not reached by Skyver » Sun, 2022-01-23 10:53 |
0 |
by Skyver Sun, 2022-01-23 10:53 |
|
|
Running PID position Control with FOC sensorless by talabo » Fri, 2021-12-03 17:21 |
0 |
by talabo Fri, 2021-12-03 17:21 |
|
|
Connecting AMT203 to Flipsky 4.20 ESC by kgeo0003 » Mon, 2022-01-24 06:44 |
0 |
by kgeo0003 Mon, 2022-01-24 09:00 |
|
|
Autonomous RC car with Focbox suddenly stops by Autocar » Mon, 2021-12-06 06:55 |
0 |
by Autocar Mon, 2021-12-06 06:55 |
|
|
Incorrect Batt Current Readings in FOC but not in BLDC by vadicus » Tue, 2020-02-25 20:06 |
0 |
by vadicus Tue, 2020-02-25 20:09 |
|
Log in to post new content in the forum.
