You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Spin motor at constant ERPM while a button is pressed by t-dub-maui » Fri, 2024-01-26 07:33 |
0 |
by t-dub-maui Fri, 2024-01-26 07:33 |
|
|
Designing a robust power stage using Mosfets by ripperpc » Tue, 2020-05-05 08:04 |
0 |
by ripperpc Tue, 2020-05-05 08:04 |
|
|
VESC Express GPS Logging frequency by steveeng » Tue, 2025-03-25 22:55 |
0 |
by steveeng Tue, 2025-03-25 22:55 |
|
|
ADC INPUT with 4.10 HW running with 5.02 FW by mouadh » Tue, 2022-03-22 15:32 |
0 |
by mouadh Tue, 2022-03-22 17:38 |
|
|
Wolf king 11 gt 72v perimeters Help by jsherbz92 » Tue, 2025-04-01 05:52 |
0 |
by jsherbz92 Tue, 2025-04-01 05:52 |
|
|
What motors can i use with the vesc? by bengce » Sun, 2020-06-14 22:28 |
0 |
by bengce Sun, 2020-06-14 22:28 |
|
|
Remote pairs but motor does not spin after VESC tool use by frunobulax » Fri, 2025-04-11 18:26 |
0 |
by frunobulax Fri, 2025-04-11 18:26 |
|
|
Flipsky 75100 + tft screen by omrishalev123 » Mon, 2024-12-30 23:10 |
0 |
by omrishalev123 Mon, 2024-12-30 23:10 |
|
|
Voltage on motor leads @ 0 throttle by SimpleUnmanned » Thu, 2020-05-21 02:40 |
0 |
by SimpleUnmanned Thu, 2020-05-21 02:40 |
|
|
Is BMS Tool compatible with LTO batteries? by SteveBrantley » Fri, 2025-04-18 23:12 |
0 |
by SteveBrantley Fri, 2025-04-18 23:12 |
|
|
75100 recognized as 75300 and nothing works by anaka » Mon, 2025-01-20 19:59 |
0 |
by anaka Mon, 2025-01-20 19:59 |
|
|
What is the current state of mcus support? by il_piccione » Fri, 2025-04-25 09:47 |
0 |
by il_piccione Fri, 2025-04-25 09:47 |
|
|
PPM+UART. RC and esp32 by coldreboot » Thu, 2025-01-30 23:20 |
0 |
by coldreboot Fri, 2025-01-31 15:50 |
|
|
Adjusting Acceleration Ramp with NRF & Current control by Mido » Tue, 2022-04-05 14:36 |
0 |
by Mido Tue, 2022-04-05 14:36 |
|
|
How to set dead time on BLDC mode? by AllenFF » Wed, 2020-04-15 03:30 |
0 |
by AllenFF Mon, 2020-04-27 15:34 |
|
|
Flipsky 75200 Motor ruckelt und wird sehr schnell heiß by Oriessin » Sat, 2025-04-26 07:38 |
0 |
by Oriessin Sat, 2025-04-26 07:38 |
|
|
Best Throttle and break level by ardillolambo » Wed, 2022-03-02 18:29 |
0 |
by ardillolambo Wed, 2022-03-02 18:29 |
|
|
Measurement of voltage and mah by renaudbarbier » Sun, 2020-05-31 17:04 |
0 |
by renaudbarbier Sun, 2020-05-31 17:04 |
|
|
Vesc firmware to programmable Sabvoton ml60 controller. by Maciejwarloch » Tue, 2022-03-08 14:19 |
0 |
by Maciejwarloch Tue, 2022-03-08 14:19 |
|
|
VESC Connect dongle alternatives by Pimousse » Tue, 2020-06-02 15:32 |
0 |
by Pimousse Tue, 2020-06-02 15:32 |
|
|
Battery charging using motor inductance by eptv » Sun, 2020-04-26 07:44 |
0 |
by eptv Sun, 2020-04-26 07:44 |
|
|
Flipsky screen for Ubox driver help! by Dostawca.L » Sat, 2025-02-22 19:20 |
0 |
by Dostawca.L Sat, 2025-02-22 19:20 |
|
|
Motor compatibility (and power levels) by MrSurly » Tue, 2022-04-12 21:43 |
0 |
by MrSurly Tue, 2022-04-12 21:43 |
|
|
vesc 75100 variations for a kart build by elbracer » Mon, 2025-05-19 19:57 |
0 |
by elbracer Mon, 2025-05-19 19:57 |
|
|
Servo output CAN Formats by vinci » Mon, 2022-04-18 15:35 |
0 |
by vinci Mon, 2022-04-18 15:35 |
Log in to post new content in the forum.
