You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Under rated VESC for motor, problem? by Alistair Goodman » Wed, 2022-08-03 12:53 |
2 |
by Alistair Goodman Wed, 2022-08-03 15:27 |
|
|
IPM/Salient Motor Tuning by SRFirefox » Wed, 2020-08-26 23:19 |
2 |
by JP Wed, 2022-08-17 11:22 |
|
|
Running motors under 900ERPM in speed control by Chieflouis01 » Thu, 2025-11-27 21:32 |
2 |
by Chieflouis01 Thu, 2025-11-27 21:33 |
|
|
The motor with an enkoder of AS5048 rotates unevenly by densor » Thu, 2018-04-26 11:41 |
2 |
by densor Fri, 2018-04-27 08:27 |
|
|
Reprogram VESC for sensorless motor by Christopherinco... » Thu, 2020-09-03 00:10 |
2 |
by vadicus Thu, 2020-09-03 01:14 |
|
|
Flipsky 72150 outboard cannot connect via USB by EddieEagle1970 » Sat, 2026-02-21 16:56 |
2 |
by mariuszdymon Sat, 2026-02-28 23:37 |
|
|
PAS with variable assist+regen brake by Lukas_T » Fri, 2025-08-29 18:05 |
2 |
by Lukas_T Fri, 2025-10-31 10:28 |
|
|
Flipsky motor and flipsky FSESC, can't move when weighted/under load. by adamgil801 » Fri, 2022-07-01 23:17 |
2 |
by Indy8976 Mon, 2022-07-11 11:21 |
|
|
Motor Overheating in FOC by amanpereira1 » Thu, 2022-05-05 16:14 |
2 |
by Nuppen Wed, 2024-02-14 08:14 |
|
|
Flipsky 75100 pro v2 ADC throttle stopped responding by JozoBozo » Tue, 2026-02-24 17:33 |
2 |
by JozoBozo Sun, 2026-03-01 13:40 |
|
|
Throttle mapping issue by forcefed » Fri, 2018-03-30 15:37 |
2 |
by Burak Thu, 2023-12-07 13:21 |
|
|
Timeout Brake Current [Fail Save] by Cuprani » Mon, 2018-04-02 00:03 |
2 |
by Cuprani Tue, 2018-04-03 12:28 |
|
|
Real RPM=0 but ERPM>0 issue by cir7 » Tue, 2022-07-12 20:17 |
2 |
by cir7 Wed, 2022-07-13 11:43 |
|
|
Type of motors supported by VESC 6 MKIV by Sami Sahli » Thu, 2020-06-25 11:57 |
2 |
by Samuelx Tue, 2021-08-17 20:24 |
|
|
AS5048A and the AS5047D Problems. by raess » Wed, 2018-04-04 14:05 |
2 |
by liqikai Thu, 2018-09-13 10:47 |
|
|
Can bus and Arduino by Snabelost » Wed, 2023-06-14 10:30 |
2 |
by Snabelost Thu, 2023-06-15 08:37 |
|
|
limits to reprogramming VESCs by wjpremerlani » Wed, 2023-06-21 09:11 |
2 |
by wjpremerlani Thu, 2023-06-22 20:13 |
|
|
<SOLVED> Terms defined / bldc "vs." vesc_tool by Gos1 » Tue, 2023-06-27 12:32 |
2 |
by Gos1 Fri, 2024-01-26 10:54 |
|
|
Axiom with SIN/COS encoder and Motoenergy ME1304 by Boben » Sat, 2021-03-20 20:51 |
2 |
by Boben Sun, 2021-03-21 10:03 |
|
|
VESC 100/250: analog regen brake AND e-brake cut switch? by fatty » Thu, 2021-05-13 01:16 |
2 |
by frank Mon, 2022-05-02 09:11 |
|
|
Custom code changes- I/O pin go high or low by dsuresh » Thu, 2021-05-13 19:50 |
2 |
by dsuresh Fri, 2021-05-14 22:30 |
|
|
just receaved my awesome new vesc 6 plus however it wont configurate i get an errot message. :( by sabladask » Wed, 2023-05-03 16:15 |
2 |
by frank Fri, 2023-05-05 20:54 |
|
|
Battery to motor voltage by fazekas » Sat, 2021-05-15 16:03 |
2 |
by fazekas Sun, 2021-05-16 20:43 |
|
|
Gyro/Accel utilisation for built in Alarm ?! :D by yoodog » Tue, 2021-03-30 00:48 |
2 |
by yoodog Tue, 2021-03-30 01:07 |
|
|
Motor is "pumping" under load in current control mode. is this normal? by etienne » Sat, 2023-05-13 17:16 |
2 |
by iv.kravchenko Sat, 2023-05-20 08:31 |
Log in to post new content in the forum.
