You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
what is HFI in the VESC? by dcameron » Sat, 2022-11-19 00:14 |
2 |
by dcameron Mon, 2022-11-21 02:07 |
|
|
VESC Tool cannot connect to VESC by Ecuashungo » Mon, 2021-02-08 13:20 |
2 |
by district9prawn Fri, 2021-02-12 01:48 |
|
|
Porting vesc to this closed source controller? by st0r » Sat, 2023-01-28 19:07 |
2 |
by jaykup Tue, 2023-01-31 03:05 |
|
|
Hoverboard motors not spinning when manually controlled, work when doing hall test etc. by VK2EVA » Fri, 2020-12-25 22:01 |
2 |
by ATHIVEL Thu, 2021-02-18 15:45 |
|
|
VESC 100/250 For sale by jakemansbach » Sun, 2023-02-05 04:22 |
2 |
by EliProtiva Tue, 2023-02-28 00:12 |
|
|
HALL-FOC---don't understand the mcpwm_foc_hall_detect() function by ConnerL » Wed, 2021-01-06 12:33 |
2 |
by ConnerL Tue, 2021-01-12 02:55 |
|
|
Hardware circuit to limit regen voltage by Gsorter » Sun, 2023-02-05 17:34 |
2 |
by Gsorter Tue, 2023-02-07 17:41 |
|
|
VESC and T500 Thruster - Problems obtaining right speed by SIGURD » Tue, 2022-12-13 13:45 |
2 |
by SIGURD Wed, 2022-12-14 16:20 |
|
|
Adding a Openloop COMM Comand by JulianT » Sun, 2021-01-17 21:27 |
2 |
by JulianT Mon, 2021-02-15 12:17 |
|
|
Why switchable current filters? by BillyJ » Sat, 2019-10-05 12:22 |
2 |
by shaman Sun, 2019-10-13 17:41 |
|
|
Synchronizing multiple motors before mechanically locking together by hockinsk » Sun, 2019-10-27 23:15 |
2 |
by Stupidspencer Sun, 2019-12-15 22:50 |
|
|
Flipsky 75200 with 80100 80kv by ors150 » Tue, 2021-09-14 20:03 |
2 |
by Oded Mazor Sat, 2022-06-04 15:17 |
|
|
Encoder disconnection caused shoot through mosfet fire during regen? by devmonkey » Sun, 2021-11-07 18:17 |
2 |
by devmonkey Mon, 2021-11-08 12:21 |
|
|
VESC Telemetry FPV by karabey08 » Tue, 2019-11-19 15:19 |
2 |
by frank Wed, 2019-11-20 11:03 |
|
|
IMU support and alternate IMU ICs (Bosch bmi160?) by shaman » Fri, 2019-09-20 15:04 |
2 |
by shaman Thu, 2019-10-03 19:06 |
|
|
Braking noisy on Hoverboards hubs . by lurch » Mon, 2021-11-08 15:59 |
2 |
by lurch Mon, 2021-11-15 21:35 |
|
|
Erratic braking on vesc using large hub motor. by jtechbop » Sun, 2021-09-19 06:54 |
2 |
by jtechbop Tue, 2021-10-19 20:59 |
|
|
VESC vs HobbyWing...whats going on with the AMPS? by maljan » Mon, 2021-09-20 23:34 |
2 |
by drummerboy5408 Tue, 2021-09-21 03:41 |
|
|
Hardware fault troubleshooting by thewho » Sat, 2020-08-15 16:50 |
2 |
by thewho Tue, 2020-08-18 00:07 |
|
|
CAN Communication Between Three or More VESCs by mksonic » Tue, 2026-05-26 03:34 |
2 |
by mksonic Wed, 2026-05-27 05:30 |
|
|
Extending current shunt amplifier voltage by TechAUmNu » Wed, 2018-04-11 00:43 |
2 |
by Roger Wolff Tue, 2018-04-17 08:56 |
|
|
Trampa 100/250 with Cyc x1pro motor high Rpm issue PLZ Help :) by Asi » Thu, 2022-07-28 10:08 |
2 |
by Asi Thu, 2022-07-28 16:12 |
|
|
Issue connecting to ESC 4.12 by Kirkness » Wed, 2020-07-08 01:40 |
2 |
by thefallen Thu, 2020-07-09 18:01 |
|
|
Motor stopped and I had to run Setup Motors FOC wizard to get it going again by JasonBear » Fri, 2025-11-14 13:24 |
2 |
by JasonBear Sun, 2025-11-16 20:41 |
|
|
Which encoders are supported? by raess » Thu, 2018-03-22 23:38 |
2 |
by raess Fri, 2018-03-23 22:58 |
Log in to post new content in the forum.
