You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Flux linkage detection failed by Count1310 » Sat, 2020-08-22 16:30 |
3 |
by drummerboy5408 Wed, 2022-04-13 07:42 |
|
|
Ideal Thermistor/Temperature Sensor? by josh » Sat, 2017-10-14 07:07 |
3 |
by josh Sun, 2017-10-22 06:52 |
|
|
Cant get Rotor position to work by nancio » Mon, 2022-06-06 20:47 |
3 |
by frank Thu, 2022-06-09 09:05 |
|
|
Wiring a touchscreen to a vesc by posthy » Tue, 2022-06-14 10:22 |
3 |
by frank Thu, 2022-06-16 08:35 |
|
|
Set McConf with no values --> bootloader erased? by Kakskiv » Tue, 2017-11-28 12:52 |
3 |
by basti30 Wed, 2018-08-22 22:22 |
|
|
Open source hardware? by Jens » Thu, 2017-09-14 18:15 |
3 |
by frank Fri, 2017-09-15 14:01 |
|
|
VESC6+ compatible 540 1/10 BLDC motor recommendation by henry10210 » Tue, 2019-12-17 08:15 |
3 |
by benjamin Sun, 2019-12-22 09:56 |
|
|
Optimizing VESC6 setup for my Giant Lego Go-Kart project by mantisrobot » Thu, 2020-06-18 13:29 |
3 |
by TechAUmNu Mon, 2020-06-29 10:19 |
|
|
UART Accel/Gyro/Mag data by NATUITION » Sat, 2019-12-28 11:25 |
3 |
by NATUITION Tue, 2020-01-07 22:14 |
|
|
VESC API? by ufechner » Sun, 2018-03-11 14:05 |
3 |
by vimi94 Fri, 2019-05-03 18:45 |
|
|
Downloading VESC tool on a mac? by Taliesin » Mon, 2018-04-30 01:28 |
3 |
by txdad Fri, 2021-08-27 17:41 |
|
|
Error 500 on older private messages by TechAUmNu » Wed, 2018-05-09 23:15 |
3 |
by Roger Wolff Mon, 2018-05-14 10:06 |
|
|
Potentiometer control by khadra.m123 » Thu, 2018-04-05 08:51 |
3 |
by slapshot136 Sun, 2018-04-08 00:07 |
|
|
when speed of vesc motor too fast and the arduino pin signal is unstable by HumorLogic » Tue, 2021-04-06 14:21 |
3 |
by woliam Sat, 2021-04-10 15:17 |
|
|
VESC CAN_STATUS_1_2_3_4 explained (RPi) by kimpet » Mon, 2019-05-13 12:51 |
3 |
by Jack_Li Tue, 2019-07-30 14:01 |
|
|
VESC Input Using Raspberry Pi and Wiimote by Schizug » Wed, 2019-03-27 04:28 |
3 |
by Nelf Sat, 2020-08-08 01:13 |
|
|
what is this part for by ynoo443 » Wed, 2024-10-23 16:57 |
3 |
by ynoo443 Wed, 2024-10-23 17:02 |
|
|
Lanyard kill switch by craig w » Mon, 2022-01-03 09:30 |
3 |
by ewakegermanyhq Wed, 2022-08-03 16:55 |
|
|
How to prevent ground loop? by mansi712 » Fri, 2024-11-01 17:46 |
3 |
by Spaceman Thu, 2024-12-05 14:23 |
|
|
Undervoltage Fault by gazlinux » Tue, 2022-02-08 02:26 |
3 |
by 67RS427 Fri, 2022-10-21 20:53 |
|
|
How to reverse direction from VESC UART? by vinchi » Sat, 2022-01-08 23:03 |
3 |
by ergnmnh Thu, 2023-11-30 09:54 |
|
|
Advice needed: How to select KV value (or: how important is KV, in reality?) by c0d3z3r0 » Tue, 2024-09-03 09:23 |
3 |
by Groundspeed100 Tue, 2025-03-11 15:23 |
|
|
Can larger BLDC motors be controlled with VESC? by Heimfried » Sun, 2020-02-02 21:29 |
3 |
by Heimfried Thu, 2020-02-06 22:39 |
|
|
Can’t connect VESC tool to my ESC. Pls help by Comeback10 » Mon, 2024-09-16 23:08 |
3 |
by Spaceman Thu, 2024-12-19 20:11 |
|
|
VESC setup question for a motorised rope ascender. by Ben26 » Wed, 2024-10-02 18:57 |
3 |
by Ben26 Fri, 2024-10-18 01:08 |
Log in to post new content in the forum.
