You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
throttle set up by TONY61 » Wed, 2024-12-11 16:48 |
4 |
by Jamesavery22 Sun, 2025-01-05 10:54 |
|
|
Full Throttle direct after input deadband by toerde » Sat, 2022-04-30 18:54 |
4 |
by frank Mon, 2022-05-09 08:22 |
|
|
Problem with regenerative breaking by ligi » Sat, 2022-04-02 15:08 |
4 |
by ligi Sat, 2023-07-15 02:02 |
|
|
Nothing works for MY1020 3kw 72v motor and flipsky75100 by Valérian Pigeon » Tue, 2025-02-04 16:49 |
4 |
by Valérian Pigeon Thu, 2025-02-06 20:59 |
|
|
Burned my VESC 6 MKV. Wrong polarity by okhsunrog » Thu, 2022-04-07 01:44 |
4 |
by frank Thu, 2022-04-07 10:27 |
|
|
Flipsky 75/100 Mosfet short? by Michael Campbell » Mon, 2022-04-11 08:29 |
4 |
by Michael Campbell Tue, 2022-04-12 00:03 |
|
|
FOC : Stop Motor without Active Brake by Flyingtux » Mon, 2022-03-14 12:35 |
4 |
by Flyingtux Tue, 2022-03-15 23:09 |
|
|
Improved low speed and full stop control with Hall by pf26 » Mon, 2020-06-08 19:33 |
4 |
by pf26 Tue, 2020-09-22 17:34 |
|
|
Stall torque in sensorless mode by cromoly » Sun, 2018-11-25 07:54 |
4 |
by spork Thu, 2018-11-29 03:23 |
|
|
vesc6 help with hub motor by badger1666 » Thu, 2018-12-20 18:36 |
4 |
by badger1666 Fri, 2018-12-21 06:03 |
|
|
Control singular VESC using CAN-BUS and Arduino by Cam » Wed, 2021-01-06 10:29 |
4 |
by craiggault Wed, 2022-04-27 23:07 |
|
|
ADC1 problems with Firmware/Hardware issue? by sam.vanratt » Thu, 2018-12-27 22:31 |
4 |
by sam.vanratt Thu, 2019-01-03 17:46 |
|
|
Position control with Hall and A/B encoder by jo.rauchfuss » Tue, 2019-12-17 04:12 |
4 |
by frank Thu, 2019-12-19 21:09 |
|
|
VESC 75/300 + ~20kW motor , bms configuration problem... by gucho » Sat, 2019-10-26 14:45 |
4 |
by hockinsk Mon, 2019-10-28 21:33 |
|
|
Overvoltage Error during setup by arranto12 » Mon, 2021-11-08 23:22 |
4 |
by electricfox Tue, 2025-02-04 19:28 |
|
|
Axiom's ESC with BLDC for Electric Motorcycle Conversion by ardillolambo » Tue, 2021-09-21 00:57 |
4 |
by alexrentier Thu, 2021-09-30 14:30 |
|
|
ADC control not linear or smooth by arranto12 » Sat, 2021-11-13 23:23 |
4 |
by TechAUmNu Sun, 2021-11-14 01:03 |
|
|
Difference between Brake Current, Full Brake etc by wdaehn » Wed, 2018-02-21 15:32 |
4 |
by rodread Sat, 2018-03-03 10:45 |
|
|
Firmware update thru UART? by cromoly » Tue, 2018-04-17 01:19 |
4 |
by cromoly Fri, 2018-04-20 19:22 |
|
|
Charge wires by Phill Dixon » Tue, 2017-10-24 14:24 |
4 |
by linsus Tue, 2017-11-21 14:39 |
|
|
Removing low speed openloop FOC parking brake mode from FW by rodread » Thu, 2018-03-08 15:01 |
4 |
by arvidb Wed, 2018-06-06 19:02 |
|
|
Battery power by Phill Dixon » Tue, 2017-11-14 20:14 |
4 |
by slapshot136 Tue, 2017-11-21 05:01 |
|
|
E-Bike Throttle connect with Regenerative Braking by E-Toxx » Sat, 2017-09-09 09:38 |
4 |
by Jacki Villis Thu, 2019-05-16 14:43 |
|
|
Can motor parameters be detected with shaft load? by powerlabor001 » Thu, 2018-03-15 13:24 |
4 |
by powerlabor001 Sat, 2018-03-24 03:07 |
|
|
Smooth control 3 phase sensored motor by spacewalker » Thu, 2020-07-23 07:25 |
4 |
by vadicus Fri, 2020-11-13 19:18 |
Log in to post new content in the forum.
