You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Wand Cruise Control, and speed control only working on Master VESC by MaddiQ » Mon, 2019-09-16 20:46 |
15 |
by hans_maier Fri, 2019-10-11 00:22 |
|
|
Power switch on VESC 6 MK III by hans_maier » Mon, 2020-01-20 23:35 |
16 |
by Mantis13 Wed, 2024-07-31 12:52 |
|
|
simulate turboprop engine ... using VESC, how to.... by Eckehard » Wed, 2020-06-10 22:32 |
17 |
by Eckehard Thu, 2020-07-02 22:34 |
|
|
Hall sensor filter on VESC flier board by raess » Tue, 2018-03-27 21:00 |
17 |
by raess Wed, 2018-04-11 13:43 |
|
|
3 speed switch by de-bodgery » Sat, 2021-08-21 02:22 |
17 |
by Oscar Lozano Gimenez Mon, 2023-05-22 14:07 |
|
|
Two vescs, one motor? by RoopeKuisma » Sun, 2020-05-10 22:11 |
17 |
by Elwin Thu, 2021-10-28 09:48 |
|
|
Current Sensing in VESC by Toshi Sharma » Fri, 2021-11-26 08:51 |
17 |
by Toshi Sharma Tue, 2022-01-04 11:46 |
|
|
VESC with really high KV by bengce » Sun, 2020-06-21 11:18 |
18 |
by bengce Thu, 2020-08-13 14:11 |
|
|
FOC and very low speeds by verbeek » Mon, 2018-07-09 16:17 |
18 |
by Chris Barth Fri, 2023-11-10 04:45 |
|
|
position control with gearbox by raess » Tue, 2018-09-25 23:48 |
18 |
by IanG Mon, 2020-03-30 06:44 |
|
|
Is electronic brake always REGEN? by Tilman Baumann » Tue, 2018-04-10 11:16 |
19 |
by henxan Sun, 2019-11-17 18:30 |
|
|
Efficiency Control by devin » Sat, 2018-09-29 19:50 |
19 |
by devin Wed, 2019-07-10 19:35 |
|
|
Using a VESC V4.12 for a machining lathe by Krampas » Sun, 2019-06-09 22:16 |
19 |
by Luke264 Wed, 2021-02-17 18:53 |
|
|
UART communication by EthB » Wed, 2017-09-06 19:13 |
19 |
by stefcux Thu, 2019-08-08 03:16 |
|
|
DRV8302 sensibility by lurch » Sat, 2021-10-23 23:37 |
19 |
by lurch Sat, 2021-10-30 10:13 |
|
|
Vesc 6 motor setup fault by Davo69URX » Wed, 2017-11-29 09:22 |
21 |
by Tresor Wed, 2019-01-16 12:38 |
|
|
Dual VESC with UART communication (Arduino) - how to communicate with slave over can ? by GargiMan » Thu, 2019-01-03 01:56 |
21 |
by Shubham07 Fri, 2023-03-31 10:49 |
|
|
Brake hiccup by Phill Dixon » Wed, 2022-03-30 18:23 |
23 |
by Phill Dixon Mon, 2022-04-25 17:45 |
|
|
Golden Motor HPM48-5000, reconciling winding R & L values by j.konrad » Sat, 2022-01-15 22:09 |
24 |
by j.konrad Mon, 2022-01-31 15:15 |
|
|
Tmotor U8 and VESC6 FOC by protontim » Tue, 2017-10-10 22:44 |
26 |
by magnus.w Sun, 2019-04-28 18:45 |
|
|
NOOB question: how does kV-rating relate to max/min RPM of the motor? by Henque19 » Mon, 2019-12-02 17:52 |
27 |
by Gmack Sun, 2020-10-04 18:27 |
|
|
Autodetection values way off by thewho » Sat, 2019-05-25 20:34 |
28 |
by vadicus Mon, 2023-06-19 20:22 |
|
|
FOC braking problem (FAULT_CODE_DRV) by iscle » Tue, 2018-05-29 15:16 |
29 |
by Zanooon97 Sat, 2023-03-18 20:11 |
|
|
Stuck at 150 battery amps... by AlexLTDLX » Sun, 2022-02-13 03:00 |
37 |
by AlexLTDLX Sat, 2022-05-21 20:03 |
|
|
I cant get my scooter to work correct it make some strange sounds by vallsta » Sun, 2021-05-16 03:19 |
39 |
by svs Thu, 2022-01-13 07:53 |
Log in to post new content in the forum.
