You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Harsh noise on rapid/high current acceleration, please help! (with images and video!) by steveeng » Sat, 2024-12-28 15:56 |
7 |
by steveeng Mon, 2024-12-30 17:21 |
|
|
VESC crashes on Servo output by AutonomousDrifting » Fri, 2021-02-05 13:25 |
7 |
by dawgs Sat, 2025-04-19 12:40 |
|
|
Newby RPM question by dirkske » Mon, 2018-06-18 23:00 |
7 |
by dirkske Wed, 2018-06-20 20:45 |
|
|
Sensorless ERPM confusion and cogging in FOC by Addy » Mon, 2018-05-14 22:38 |
7 |
by bayetan Sun, 2023-06-04 17:19 |
|
|
Switch two Motor Profiles/Modes (UART) by anli » Thu, 2018-08-16 19:02 |
7 |
by basti30 Sun, 2018-09-30 19:55 |
|
|
coms port bluetooth and switch and adc ? by badger1666 » Tue, 2017-12-12 17:20 |
7 |
by Ampit Fri, 2023-12-22 13:34 |
|
|
Getting IMU Data over UART by Mido » Wed, 2021-04-21 12:30 |
7 |
by MrFobwatch Fri, 2024-03-15 03:05 |
|
|
Fast Startup problem by sam.vanratt » Thu, 2019-01-03 17:56 |
7 |
by sam.vanratt Sun, 2019-01-06 23:25 |
|
|
VESC in Road Vehicle by hockinsk » Sun, 2020-10-18 13:57 |
7 |
by vadicus Tue, 2020-10-27 04:58 |
|
|
Motor jitters and skips poles, but only in one direction by L0laapk3 » Mon, 2022-09-19 21:32 |
7 |
by frank Wed, 2022-09-21 09:07 |
|
|
Alien Power Systems Hall Sensors with VESC6 by lazerusrm » Tue, 2018-03-13 02:52 |
8 |
by faulknernolan Tue, 2022-07-05 11:36 |
|
|
Failure of FOC mode brake by jzy1115 » Sun, 2018-03-25 10:23 |
8 |
by iscle Sun, 2018-07-15 19:19 |
|
|
VESC as Generator - Low Output at High Brake Current? by hoeken » Sat, 2021-08-28 17:42 |
8 |
by flydr2 Wed, 2023-04-12 20:38 |
|
|
Is there a VESC with the form factor like a Votol EM200 ? (with those threaded lugs|Screw Terminals)) by Gatze » Sat, 2022-03-12 09:33 |
8 |
by qdxiatao Sat, 2022-08-20 04:09 |
|
|
Newbie Help - ADC input by nickyg » Tue, 2020-04-28 11:05 |
8 |
by velolac Fri, 2021-12-10 19:40 |
|
|
Difference between the current, duty cycle and PID speed control mode by tromes » Thu, 2020-06-11 07:51 |
8 |
by Onarb Kabr Wed, 2025-01-15 13:32 |
|
|
Vesc 100/250 (Trampa board) wiring for ebike by Oded Mazor » Fri, 2022-03-18 23:34 |
8 |
by Markula Fri, 2022-04-01 09:21 |
|
|
ADC and Uart reverse button by vufmihai » Sun, 2020-01-05 22:21 |
8 |
by supertiny808 Mon, 2022-07-11 13:41 |
|
|
Protecting PSU with resistive load when braking by henxan » Sat, 2019-11-16 21:08 |
8 |
by Stupidspencer Mon, 2019-12-30 18:02 |
|
|
Why is the speed lower in FOC mode than BLDC mode ? by stone_1706 » Thu, 2019-01-17 08:23 |
8 |
by speed3r Wed, 2022-06-15 09:34 |
|
|
PPM Signal not recognized by nopf » Mon, 2024-06-17 15:31 |
8 |
by nopf Tue, 2024-07-02 15:01 |
|
|
No connection with vesc by Matthieu van Ra... » Wed, 2019-02-13 18:07 |
8 |
by sam.vanratt Thu, 2019-02-14 15:33 |
|
|
Canoe fun! Running rough/stepping at low speeds, 75200 Pro V2 ESC and 65121 Motor. by ajtalbot1 » Wed, 2024-07-31 05:49 |
8 |
by ajtalbot1 Sat, 2024-08-17 23:44 |
|
|
Recommended way to implement CAN-bus communication using a Linux based controller by toma » Tue, 2019-06-11 08:32 |
8 |
by toma Thu, 2019-06-13 07:43 |
|
|
VESC 75/300 and EMC Tests for motorcycle conversion by gotfatalErrs » Tue, 2020-06-02 18:34 |
8 |
by Bubu54 Wed, 2024-09-04 13:52 |
Log in to post new content in the forum.
