You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Noise with Hall sensor at high speed by yosoufe » Thu, 2018-03-08 12:34 |
9 |
by yosoufe Tue, 2018-03-20 09:30 |
|
|
ERPM to Rpm by faheemift » Wed, 2021-03-31 11:11 |
9 |
by faheemift Wed, 2021-04-14 13:01 |
|
|
Setting PI / PID controllers in VESC for very low speeds. For CNC by K@RLSON » Sat, 2020-01-25 21:06 |
9 |
by Luke264 Wed, 2021-02-17 18:52 |
|
|
Acceleration control to desired RPM by bjohns » Fri, 2018-07-20 22:08 |
9 |
by arvidb Thu, 2018-08-09 21:15 |
|
|
Braking in speed PID controlled mode by vadimz » Sat, 2018-09-15 14:19 |
9 |
by zybyxutese Mon, 2019-04-01 13:35 |
|
|
Trampa VESC 100/250 suitable for heavy applications? by nojjan » Thu, 2022-12-29 13:52 |
9 |
by vadicus Wed, 2023-03-01 06:26 |
|
|
VESC settings for large scooter motor by trimen » Tue, 2020-07-14 22:15 |
9 |
by pwn1j Tue, 2024-07-02 23:30 |
|
|
Help is there an issue with my new Vesc 6 by avis » Sat, 2017-09-30 15:21 |
9 |
by frank Wed, 2017-10-04 17:10 |
|
|
Serial Connection Lost with Vesc6.6 Firmware 5.2 and Vesc Tool 3.0 by Dan Slanker » Wed, 2021-04-28 16:56 |
9 |
by AngelKillR Wed, 2022-09-28 05:10 |
|
|
Failure in Motor Set Up by Toshi Sharma » Tue, 2022-01-11 15:19 |
9 |
by frank Thu, 2022-01-13 14:15 |
|
|
Problem with Bluetooth connection (HM-10) by squdowx » Mon, 2018-07-30 15:56 |
9 |
by CTSchorsch Thu, 2019-12-05 21:27 |
|
|
VESC with Raspberry Pi 3 by Antonio Rodrígu... » Sun, 2018-06-03 18:54 |
9 |
by ShortCircuit Thu, 2018-06-28 15:33 |
|
|
VESC Questions from the newbie by mendez » Fri, 2019-02-08 21:13 |
10 |
by frank Mon, 2019-02-18 08:52 |
|
|
FOC current oscillation at max. speed by ProgramThyself » Mon, 2020-08-10 05:55 |
10 |
by SRFirefox Wed, 2020-08-26 23:10 |
|
|
Brakes completely repeatedly failing at high temperature by Paul15578 » Mon, 2018-03-26 13:06 |
10 |
by Paul15578 Sun, 2018-04-22 14:16 |
|
|
Suddenly broken by moto_guy » Fri, 2019-03-08 13:50 |
10 |
by David_1 Fri, 2022-06-17 21:07 |
|
|
VESC with auto calibration of grace one motor (videos included) by ligi » Mon, 2020-10-19 02:13 |
10 |
by ligi Tue, 2020-11-17 06:56 |
|
|
Insufficient torque at low RPM by isso777 » Sat, 2022-04-23 21:13 |
10 |
by frank Tue, 2022-05-03 08:18 |
|
|
Vesc for 5000kW QS 205 Hub Motor ebike by Amiran » Fri, 2019-09-27 15:52 |
10 |
by vadicus Sun, 2023-04-23 01:23 |
|
|
Switching frequency factor 2 lower by Elwin » Sat, 2021-11-13 22:48 |
10 |
by Elwin Sun, 2022-01-09 08:31 |
|
|
Solved: Cruise Control: Push to Activate; Cancel on BRK or Throttle Touched by vadicus » Wed, 2020-01-08 23:47 |
10 |
by vadicus Sat, 2024-02-17 01:37 |
|
|
Few questions by ElectroMagneto » Thu, 2020-01-09 23:57 |
10 |
by ElectroMagneto Sat, 2020-01-11 00:45 |
|
|
Noised signal from motor NTC sensor | HW4.12 FW3.27 by ma-j-sterelektron » Wed, 2017-09-06 18:41 |
10 |
by vescsci Wed, 2020-07-15 22:47 |
|
|
Dual VESC, Dual UART? by kneave » Mon, 2020-08-17 22:00 |
10 |
by Duane Degn Mon, 2020-08-24 00:23 |
|
|
about reference hardware by qdxiatao » Mon, 2017-09-25 08:32 |
10 |
by lizardmech Tue, 2017-11-21 19:40 |
Log in to post new content in the forum.
