You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Repurposed Hyundai Ioniq HSG Hybrid Starter Generator as motor - crunching/cogging by patracy » Sat, 2025-04-12 04:42 |
0 |
by patracy Sat, 2025-04-12 04:42 |
|
|
What constitutes a continuous vs burst current? by Alistair Goodman » Tue, 2025-01-07 16:08 |
0 |
by Alistair Goodman Tue, 2025-01-07 16:08 |
|
|
How the saliency is affecting the High frequency signal injection? by SOURAV UK » Sun, 2020-05-03 11:35 |
0 |
by SOURAV UK Sun, 2020-05-03 11:35 |
|
|
When SWD Program Connect Fails by canoeman » Mon, 2022-02-28 18:32 |
0 |
by canoeman Mon, 2022-02-28 18:32 |
|
|
PPM Arduino throttle AND UART Bluetooth Monitor AND brake lever for braking by vescsci » Fri, 2020-06-12 10:55 |
0 |
by vescsci Fri, 2020-06-12 10:55 |
|
|
Using UART from LabVIEW by hannnes » Tue, 2022-04-05 15:19 |
0 |
by hannnes Tue, 2022-04-05 15:19 |
|
|
DRV Fault at high load by mikoyas » Sat, 2020-06-13 15:43 |
0 |
by mikoyas Sat, 2020-06-13 15:43 |
|
|
9 by RoopeKuisma » Sun, 2020-05-10 21:58 |
0 |
by RoopeKuisma Sun, 2020-05-10 21:58 |
|
|
Query: Can I run my 70-pole motor using a VESC-based Flipskey controller? by avaid » Thu, 2025-05-08 12:57 |
0 |
by avaid Tue, 2025-05-13 08:02 |
|
|
Stop motor after certain number of rounds by Gawarmel » Wed, 2025-02-19 12:51 |
0 |
by Gawarmel Wed, 2025-02-19 12:51 |
|
|
run one motor and off other using uart data over bluetooth by Raja Sharma » Sun, 2020-06-14 13:16 |
0 |
by Raja Sharma Mon, 2020-06-15 20:08 |
|
|
Connecting handlebar controlls by mannberg » Thu, 2022-03-10 14:57 |
0 |
by mannberg Thu, 2022-03-10 14:57 |
|
|
Motor seize and ERPM current ramp speed by krabsheva » Tue, 2025-05-13 06:49 |
0 |
by krabsheva Tue, 2025-05-13 07:00 |
|
|
low speed / high friction startup, max torque by schnedan » Mon, 2025-02-24 10:18 |
0 |
by schnedan Mon, 2025-02-24 10:19 |
|
|
Motor picks random direction when starting with HFI by TechAUmNu » Tue, 2020-06-16 00:47 |
0 |
by TechAUmNu Tue, 2020-06-16 11:06 |
|
|
Cruise control by palaga » Tue, 2025-05-20 09:20 |
0 |
by palaga Tue, 2025-05-20 09:20 |
|
|
Where can I ask technical questions about products? by MrSurly » Tue, 2022-04-19 05:22 |
0 |
by MrSurly Tue, 2022-04-19 05:22 |
|
|
FOC settings are working in one VESC hardware and not in another VESC hardware with same hardware version ( VESC 6MKVI ) by Pranit Bhamare » Fri, 2023-02-17 07:17 |
0 |
by Pranit Bhamare Fri, 2023-02-17 07:17 |
|
|
Where to find CAN protocol documentation? by doctarr » Tue, 2020-12-29 15:33 |
0 |
by doctarr Tue, 2020-12-29 15:33 |
|
|
Why not using interrupt for Hall signal detection? by kuan » Sun, 2021-01-03 09:51 |
0 |
by kuan Sun, 2021-01-03 09:51 |
|
|
Impact of motor resistance value vs temperature by Torbjorn » Fri, 2022-12-16 09:09 |
0 |
by Torbjorn Fri, 2022-12-16 09:09 |
|
|
Using vesc between many motors by EliProtiva » Tue, 2021-02-16 05:32 |
0 |
by EliProtiva Tue, 2021-02-16 05:32 |
|
|
Simultaneous control of two BLDC motors with VESCs via CAN bus without RC controller by sampatsr » Mon, 2023-02-27 20:21 |
0 |
by sampatsr Mon, 2023-02-27 20:21 |
|
|
Need help with brushed fc 24 bolt motor control by searth » Sun, 2022-12-18 16:05 |
0 |
by searth Sun, 2022-12-18 16:05 |
|
|
dual vesc question by badger1666 » Sun, 2018-10-28 12:59 |
0 |
by badger1666 Sun, 2018-10-28 12:59 |
Log in to post new content in the forum.
