You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Connect 4 vesc with can-bus, motors stuttering by oyvinla » Tue, 2022-01-04 17:12 |
8 |
by ahanktcd Wed, 2024-04-17 06:35 |
|
|
Tell me how to accurately determine the type of engine FOC, BLDC by Valera1996 » Sun, 2020-02-09 18:53 |
8 |
by vadicus Mon, 2020-02-17 22:41 |
|
|
Failure of FOC mode brake by jzy1115 » Sun, 2018-03-25 10:23 |
8 |
by iscle Sun, 2018-07-15 19:19 |
|
|
Is this kogging and jitter in low rpms expected? by Snabelost » Sat, 2022-10-22 16:53 |
8 |
by Snabelost Fri, 2022-10-28 16:07 |
|
|
VESC Battery Packs by frank » Tue, 2020-10-13 15:21 |
8 |
by zhivko Sat, 2024-08-10 21:14 |
|
|
Alien Power Systems Hall Sensors with VESC6 by lazerusrm » Tue, 2018-03-13 02:52 |
8 |
by faulknernolan Tue, 2022-07-05 11:36 |
|
|
VESC as Generator - Low Output at High Brake Current? by hoeken » Sat, 2021-08-28 17:42 |
8 |
by flydr2 Wed, 2023-04-12 20:38 |
|
|
Is there a VESC with the form factor like a Votol EM200 ? (with those threaded lugs|Screw Terminals)) by Gatze » Sat, 2022-03-12 09:33 |
8 |
by qdxiatao Sat, 2022-08-20 04:09 |
|
|
Newbie Help - ADC input by nickyg » Tue, 2020-04-28 11:05 |
8 |
by velolac Fri, 2021-12-10 19:40 |
|
|
Vesc 100/250 (Trampa board) wiring for ebike by Oded Mazor » Fri, 2022-03-18 23:34 |
8 |
by Markula Fri, 2022-04-01 09:21 |
|
|
No connection with vesc by Matthieu van Ra... » Wed, 2019-02-13 18:07 |
8 |
by sam.vanratt Thu, 2019-02-14 15:33 |
|
|
Why is the speed lower in FOC mode than BLDC mode ? by stone_1706 » Thu, 2019-01-17 08:23 |
8 |
by speed3r Wed, 2022-06-15 09:34 |
|
|
Protecting PSU with resistive load when braking by henxan » Sat, 2019-11-16 21:08 |
8 |
by Stupidspencer Mon, 2019-12-30 18:02 |
|
|
ADC and Uart reverse button by vufmihai » Sun, 2020-01-05 22:21 |
8 |
by supertiny808 Mon, 2022-07-11 13:41 |
|
|
Canoe fun! Running rough/stepping at low speeds, 75200 Pro V2 ESC and 65121 Motor. by ajtalbot1 » Wed, 2024-07-31 05:49 |
8 |
by ajtalbot1 Sat, 2024-08-17 23:44 |
|
|
PPM Signal not recognized by nopf » Mon, 2024-06-17 15:31 |
8 |
by nopf Tue, 2024-07-02 15:01 |
|
|
Recommended way to implement CAN-bus communication using a Linux based controller by toma » Tue, 2019-06-11 08:32 |
8 |
by toma Thu, 2019-06-13 07:43 |
|
|
VESC 75/300 and EMC Tests for motorcycle conversion by gotfatalErrs » Tue, 2020-06-02 18:34 |
8 |
by Bubu54 Wed, 2024-09-04 13:52 |
|
|
Communication with Vesc Tools by faheemift » Tue, 2021-02-09 16:08 |
8 |
by beatrixena Sat, 2021-02-20 09:11 |
|
|
VSEC firmware update issue by dsuresh » Thu, 2021-02-11 17:25 |
8 |
by Macc Fri, 2021-06-11 13:10 |
|
|
Using dual VESC for Robot Control by Praveen » Sat, 2021-11-13 11:02 |
8 |
by Autocar Tue, 2021-12-07 21:30 |
|
|
VESC settings for large scooter motor by trimen » Tue, 2020-07-14 22:15 |
9 |
by pwn1j Tue, 2024-07-02 23:30 |
|
|
Serial Connection Lost with Vesc6.6 Firmware 5.2 and Vesc Tool 3.0 by Dan Slanker » Wed, 2021-04-28 16:56 |
9 |
by AngelKillR Wed, 2022-09-28 05:10 |
|
|
Failure in Motor Set Up by Toshi Sharma » Tue, 2022-01-11 15:19 |
9 |
by frank Thu, 2022-01-13 14:15 |
|
|
Problem with Bluetooth connection (HM-10) by squdowx » Mon, 2018-07-30 15:56 |
9 |
by CTSchorsch Thu, 2019-12-05 21:27 |
Log in to post new content in the forum.
