You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
USB Unable to connect by Bazeljet » Thu, 2019-10-10 06:02 |
5 |
by portnawake Mon, 2019-10-28 21:42 |
|
|
(Not) Stator saturation by Stupidspencer » Sun, 2019-10-13 00:34 |
5 |
by rfedyukovich Sun, 2024-06-16 20:16 |
|
|
VESC safety by alexantosh » Tue, 2021-11-23 15:47 |
5 |
by alexantosh Tue, 2021-12-28 15:10 |
|
|
Previous tool+5.2 by Phill Dixon » Sun, 2022-05-01 07:50 |
5 |
by firemaxx Thu, 2024-07-18 09:10 |
|
|
Anti spark connector burnt my vesc? by v71n24908c27h8bn9 » Mon, 2022-07-04 12:39 |
5 |
by Spaceman Wed, 2022-07-13 16:26 |
|
|
Choppiness in motor after half throttle by popeye243 » Tue, 2020-08-04 04:04 |
5 |
by vadicus Tue, 2020-09-15 23:53 |
|
|
Design custom VESC 6 Hardware by brightlightbeam » Sat, 2020-07-04 14:18 |
5 |
by Gatze Mon, 2022-04-18 18:22 |
|
|
Rough transition to sensorless under load by vadicus » Sat, 2020-07-18 07:10 |
5 |
by vadicus Wed, 2020-08-05 20:10 |
|
|
Cannot change CAN Baudrate, Maytech SUPERFOC6.8 by sivanhere » Thu, 2023-03-23 08:12 |
5 |
by frank Mon, 2023-03-27 09:28 |
|
|
VESC TOOL ADC Voltage mapping too low. SOLVED by Ecyclist » Fri, 2018-10-19 22:38 |
5 |
by sam.vanratt Thu, 2018-11-22 20:21 |
|
|
Wiring TS5700N8501 by krassi_s » Sat, 2020-10-31 01:59 |
6 |
by TechAUmNu Tue, 2020-11-03 13:41 |
|
|
Could you recommend me a Button for turn on/off the VESC by aysubscriber@ic... » Tue, 2017-10-03 07:49 |
6 |
by e-nduro Thu, 2019-09-05 00:28 |
|
|
VESC original badge by ligi » Mon, 2020-11-02 16:00 |
6 |
by ligi Sun, 2020-11-08 03:11 |
|
|
forum search by RSR » Wed, 2017-09-06 09:52 |
6 |
by hexakopter Sat, 2017-09-23 17:16 |
|
|
Problem with tiny inrunner motor by Maxid » Tue, 2020-11-24 14:30 |
6 |
by Maxid Wed, 2020-12-09 09:51 |
|
|
Using VESC remote with non-VESC ESC by Ptkend » Tue, 2022-11-15 17:21 |
6 |
by Ptkend Sun, 2022-11-20 14:04 |
|
|
VESC for BLDC Pump- motor settings by ar5000 » Thu, 2021-06-10 10:02 |
6 |
by frank Thu, 2021-06-10 11:42 |
|
|
no speed feedback in DC mode by Jessica » Mon, 2018-11-19 11:17 |
6 |
by abrac Sat, 2019-03-30 19:11 |
|
|
Can not adjust the RPM on my 1350 w motor by Arne Norway » Wed, 2019-01-09 18:47 |
6 |
by sam.vanratt Sun, 2019-01-13 13:36 |
|
|
Why is my VESC Speed (in MPH) half what it should be? by ALarabie » Fri, 2022-12-09 17:41 |
6 |
by vadicus Sat, 2022-12-10 19:00 |
|
|
Torque control with PWM at 10kHz for LinuxCNC + MESA + AC servo by antonchromjak » Tue, 2018-03-06 08:01 |
6 |
by Artabotak Sat, 2024-01-06 09:24 |
|
|
How low is "low" inductance motors? by shaman » Sat, 2019-10-05 01:59 |
6 |
by MargaretHoffman Wed, 2023-02-22 23:07 |
|
|
Can you use both axes on a 2-axis nunchuck/joystick controller with VESC? by adamdorr » Tue, 2019-12-31 22:05 |
6 |
by sanketh1691 Sat, 2021-10-09 00:45 |
|
|
Vesc Suddenly stopped working by Erik » Wed, 2020-08-05 14:53 |
6 |
by Erik Tue, 2020-08-11 20:59 |
|
|
Flipsky 75100 and VEVOR MY1020D - Very jerky by DevelopedBug » Sat, 2022-07-16 19:46 |
6 |
by Trooth Fri, 2024-02-23 01:38 |
Log in to post new content in the forum.
