You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Hybrid mode in FOC - possible? by Oded Mazor » Tue, 2022-04-12 07:42 |
4 |
by Oded Mazor Wed, 2022-04-13 11:28 |
|
|
Pole Pairs by donrecardo » Fri, 2020-06-05 10:24 |
4 |
by Bgbalz75 Fri, 2025-05-16 13:01 |
|
|
Electric/ Gas Hybrid by kcswimrac » Wed, 2020-05-06 17:05 |
4 |
by drummerboy5408 Mon, 2022-10-24 05:43 |
|
|
Set RPM - reverse direction over CAN-Bus by 65273 » Tue, 2022-03-29 14:49 |
4 |
by 65273 Fri, 2022-04-01 15:53 |
|
|
CanOpen by maxmertins » Mon, 2023-01-30 17:10 |
4 |
by maxmertins Wed, 2023-02-01 17:24 |
|
|
Brushless or brushed motor for autonomous rc-car by Joe_Lowtech » Thu, 2018-12-20 11:56 |
4 |
by Joe_Lowtech Tue, 2019-03-05 11:00 |
|
|
Vesc tool not working by faheemift » Sun, 2021-02-14 14:44 |
4 |
by faheemift Wed, 2021-04-14 22:59 |
|
|
enertionboard focbox : is vesc_tool safe to use? by fourchette » Wed, 2018-11-07 23:49 |
4 |
by fourchette Tue, 2018-11-20 21:13 |
|
|
Using reverse with a spare channel by spork » Mon, 2018-11-26 07:08 |
4 |
by spork Tue, 2018-11-27 06:48 |
|
|
Motor Types by ellen.scott » Fri, 2021-03-05 10:50 |
4 |
by ellen.scott Tue, 2021-03-23 12:45 |
|
|
VESC Tool Instructions by brschaefer74 » Fri, 2019-01-25 03:49 |
4 |
by sam.vanratt Sat, 2019-01-26 12:52 |
|
|
UART CAN forwarding by frankus » Tue, 2019-01-29 16:07 |
4 |
by frankus Tue, 2021-02-16 06:35 |
|
|
Cannot reach max speed of BLDC motor by rousha42 » Wed, 2021-11-03 20:23 |
4 |
by frank Tue, 2021-11-09 09:46 |
|
|
PyVESC - Realtime Data - Experiment Export .csv file by Eric_IraLo » Mon, 2024-03-04 15:36 |
4 |
by Eric_IraLo Tue, 2024-04-09 11:37 |
|
|
UAVCAN vs DroneCAN vs Cypal by AndreasSkaar » Fri, 2024-05-03 22:17 |
4 |
by Williamzoe2002 Thu, 2025-03-20 10:23 |
|
|
BLDC Motor Power limitation by tecnico.solarboat » Tue, 2019-10-01 23:42 |
4 |
by tecnico.solarboat Thu, 2019-10-10 15:13 |
|
|
Setting up low KV brushless motor? by Trent » Sun, 2019-12-01 02:09 |
4 |
by Trent Wed, 2019-12-04 07:54 |
|
|
Handbrake in PPM mode by bdesvaux » Wed, 2024-03-20 17:49 |
4 |
by its4ankit Sun, 2024-05-12 17:41 |
|
|
Starting rotation by changing duty cicle- current increases shortly (ms) and dcreases immediately to 0A by simon_snow » Wed, 2021-10-06 22:15 |
4 |
by simon_snow Fri, 2021-10-08 12:49 |
|
|
Rolling down-hill faster than my board's electric top speed by koralle » Tue, 2018-05-01 21:18 |
4 |
by koralle Sun, 2018-05-06 18:25 |
|
|
MXUS 3K 5T Stuttering, Desync, Cogging sounds FSESC 75200 Pro V2 72V by djambobuksne » Mon, 2026-02-23 20:05 |
4 |
by djambobuksne Mon, 2026-03-09 19:38 |
|
|
VESC 6 hi voltage problem by mike » Fri, 2018-05-04 11:34 |
4 |
by mike Tue, 2018-05-08 19:31 |
|
|
Too little torque. by Roger Wolff » Thu, 2018-05-10 18:11 |
4 |
by Roger Wolff Mon, 2018-05-14 19:30 |
|
|
Block waves with FOC by spacemango » Fri, 2020-06-26 09:48 |
4 |
by Lisa1812 Fri, 2020-09-18 11:56 |
|
|
please delete！ by return97 » Sat, 2022-07-23 17:31 |
4 |
by return97 Wed, 2023-03-29 17:28 |
Log in to post new content in the forum.
