You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Set McConf with no values --> bootloader erased? by Kakskiv » Tue, 2017-11-28 12:52 |
3 |
by basti30 Wed, 2018-08-22 22:22 |
|
|
Open source hardware? by Jens » Thu, 2017-09-14 18:15 |
3 |
by frank Fri, 2017-09-15 14:01 |
|
|
VESC 4.20 Schematic by evbkez » Fri, 2019-09-20 07:59 |
3 |
by thefallen Fri, 2019-09-27 17:45 |
|
|
large hub motors by Frankey » Sat, 2021-11-13 19:35 |
3 |
by spacewalker Tue, 2021-11-16 13:42 |
|
|
Wand (and app) not pairing by Jonny254 » Mon, 2019-10-07 15:17 |
3 |
by Daada Wed, 2022-04-27 10:58 |
|
|
Ideal Thermistor/Temperature Sensor? by josh » Sat, 2017-10-14 07:07 |
3 |
by josh Sun, 2017-10-22 06:52 |
|
|
enertionboard focbox : is vesc_tool safe to use? by fourchette » Wed, 2018-11-07 23:49 |
4 |
by fourchette Tue, 2018-11-20 21:13 |
|
|
Smooth control 3 phase sensored motor by spacewalker » Thu, 2020-07-23 07:25 |
4 |
by vadicus Fri, 2020-11-13 19:18 |
|
|
FW=ADC1, REV=ADC2 by ProgramThyself » Sat, 2020-08-01 23:30 |
4 |
by ProgramThyself Mon, 2020-08-03 03:56 |
|
|
Using reverse with a spare channel by spork » Mon, 2018-11-26 07:08 |
4 |
by spork Tue, 2018-11-27 06:48 |
|
|
Two phase modulation by jguy » Sat, 2023-12-09 13:33 |
4 |
by jguy Fri, 2023-12-15 11:49 |
|
|
Hall Sensors Not Detected by leymane » Fri, 2023-08-18 17:12 |
4 |
by Ben26 Mon, 2024-10-21 22:45 |
|
|
Hub Motor Gives up while Coasting With No Faults by vadicus » Sun, 2020-08-09 01:36 |
4 |
by vadicus Tue, 2020-08-11 18:01 |
|
|
VESC Tool Instructions by brschaefer74 » Fri, 2019-01-25 03:49 |
4 |
by sam.vanratt Sat, 2019-01-26 12:52 |
|
|
UART CAN forwarding by frankus » Tue, 2019-01-29 16:07 |
4 |
by frankus Tue, 2021-02-16 06:35 |
|
|
Differential steering setup by GCTech » Sat, 2020-07-04 17:38 |
4 |
by CalLangford Fri, 2024-09-20 20:29 |
|
|
Brushless or brushed motor for autonomous rc-car by Joe_Lowtech » Thu, 2018-12-20 11:56 |
4 |
by Joe_Lowtech Tue, 2019-03-05 11:00 |
|
|
Updated VESC 6 schematic request by ma-j-sterelektron » Mon, 2019-03-25 08:43 |
4 |
by jejaj25773 Fri, 2024-07-26 02:29 |
|
|
half speed on FOC vs BLDC by ever.summer » Tue, 2019-05-28 00:04 |
4 |
by ever.summer Tue, 2019-05-28 04:34 |
|
|
Roll-to-start VESC by dsuresh » Fri, 2021-03-12 21:05 |
4 |
by robertkovax Fri, 2023-11-10 16:57 |
|
|
Nothing works for MY1020 3kw 72v motor and flipsky75100 by Valérian Pigeon » Tue, 2025-02-04 16:49 |
4 |
by Valérian Pigeon Thu, 2025-02-06 20:59 |
|
|
BLDC vs FOC mode， motor‘s spin direction is invert by moto_guy » Wed, 2019-02-20 11:48 |
4 |
by moto_guy Sun, 2019-02-24 09:11 |
|
|
Getting Started / Prototyping Help by harrym » Wed, 2020-04-01 17:56 |
4 |
by javmarina Sat, 2020-05-09 17:35 |
|
|
Anti cogging, suppressing torque ripple? by Alistair Goodman » Wed, 2022-01-19 11:33 |
4 |
by Alistair Goodman Thu, 2022-01-20 11:11 |
|
|
Is the Vesc 5 mkIII capable of 13s li-Ion (fully charged 54,6V) by Pelle » Sun, 2020-04-12 12:09 |
4 |
by danilolattaro Thu, 2021-04-22 14:50 |
Log in to post new content in the forum.
