You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Trampa VESC 100/250 suitable for heavy applications? by nojjan » Thu, 2022-12-29 13:52 |
9 |
by vadicus Wed, 2023-03-01 06:26 |
|
|
Serial Connection Lost with Vesc6.6 Firmware 5.2 and Vesc Tool 3.0 by Dan Slanker » Wed, 2021-04-28 16:56 |
9 |
by AngelKillR Wed, 2022-09-28 05:10 |
|
|
Failure in Motor Set Up by Toshi Sharma » Tue, 2022-01-11 15:19 |
9 |
by frank Thu, 2022-01-13 14:15 |
|
|
VESC with Raspberry Pi 3 by Antonio Rodrígu... » Sun, 2018-06-03 18:54 |
9 |
by ShortCircuit Thu, 2018-06-28 15:33 |
|
|
Problem with Bluetooth connection (HM-10) by squdowx » Mon, 2018-07-30 15:56 |
9 |
by CTSchorsch Thu, 2019-12-05 21:27 |
|
|
ERPM settings restrict carving speed on outer wheel. Poor user experience. by Paul15578 » Fri, 2018-01-12 02:28 |
9 |
by Ackmaniac Tue, 2018-04-24 13:47 |
|
|
Motor braking - shorting phases by rok340 » Thu, 2021-01-21 07:49 |
9 |
by dpeinado Mon, 2022-02-14 12:36 |
|
|
highest battery current with 6.6? by devin » Tue, 2020-01-14 16:05 |
9 |
by devin Wed, 2020-01-15 01:05 |
|
|
VESC recommendation for sailboat conversion by Henque19 » Thu, 2019-11-28 00:42 |
9 |
by Henque19 Fri, 2019-12-20 16:15 |
|
|
Noise with Hall sensor at high speed by yosoufe » Thu, 2018-03-08 12:34 |
9 |
by yosoufe Tue, 2018-03-20 09:30 |
|
|
ERPM to Rpm by faheemift » Wed, 2021-03-31 11:11 |
9 |
by faheemift Wed, 2021-04-14 13:01 |
|
|
Setting PI / PID controllers in VESC for very low speeds. For CNC by K@RLSON » Sat, 2020-01-25 21:06 |
9 |
by Luke264 Wed, 2021-02-17 18:52 |
|
|
Braking in speed PID controlled mode by vadimz » Sat, 2018-09-15 14:19 |
9 |
by zybyxutese Mon, 2019-04-01 13:35 |
|
|
Acceleration control to desired RPM by bjohns » Fri, 2018-07-20 22:08 |
9 |
by arvidb Thu, 2018-08-09 21:15 |
|
|
Insufficient torque at low RPM by isso777 » Sat, 2022-04-23 21:13 |
10 |
by frank Tue, 2022-05-03 08:18 |
|
|
Noised signal from motor NTC sensor | HW4.12 FW3.27 by ma-j-sterelektron » Wed, 2017-09-06 18:41 |
10 |
by vescsci Wed, 2020-07-15 22:47 |
|
|
about reference hardware by qdxiatao » Mon, 2017-09-25 08:32 |
10 |
by lizardmech Tue, 2017-11-21 19:40 |
|
|
VESC PAS and ADC App - How does it work? by numbke » Fri, 2023-02-24 23:49 |
10 |
by anaka Sun, 2025-01-19 17:34 |
|
|
Solved: Cruise Control: Push to Activate; Cancel on BRK or Throttle Touched by vadicus » Wed, 2020-01-08 23:47 |
10 |
by vadicus Sat, 2024-02-17 01:37 |
|
|
Few questions by ElectroMagneto » Thu, 2020-01-09 23:57 |
10 |
by ElectroMagneto Sat, 2020-01-11 00:45 |
|
|
Vesc for 5000kW QS 205 Hub Motor ebike by Amiran » Fri, 2019-09-27 15:52 |
10 |
by vadicus Sun, 2023-04-23 01:23 |
|
|
Switching frequency factor 2 lower by Elwin » Sat, 2021-11-13 22:48 |
10 |
by Elwin Sun, 2022-01-09 08:31 |
|
|
Dual VESC, Dual UART? by kneave » Mon, 2020-08-17 22:00 |
10 |
by Duane Degn Mon, 2020-08-24 00:23 |
|
|
VESC settings for large scooter motor by trimen » Tue, 2020-07-14 22:15 |
10 |
by Juzy Tue, 2025-04-01 10:58 |
|
|
FAULT_CODE_HIGH_OFFSET_CURRENT_SENSOR_3 by TB_Poule » Sat, 2021-04-10 17:26 |
10 |
by Mohanangappan Wed, 2024-09-18 16:20 |
Log in to post new content in the forum.
