You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Understanding Results from "Experiments" (sweeps) by gazlinux » Thu, 2022-02-10 02:28 |
3 |
by frank Sun, 2022-02-13 11:41 |
|
|
Dual g-foc300 setup help!!! by Re60s » Sat, 2024-09-07 09:12 |
3 |
by Tim Read Thu, 2024-09-12 16:42 |
|
|
VESC Firm for Xiaomi ESC (STM32F103) uC by Foujiwara » Sat, 2020-04-04 19:16 |
3 |
by cara Mon, 2023-08-28 04:45 |
|
|
Profiles with dual 75100 for 2wd recumbent trike by khallie06 » Tue, 2024-10-01 01:44 |
3 |
by khallie06 Fri, 2025-01-03 21:12 |
|
|
Use STM32F401CCU6 or STM32F411CEU6 in place of STM32F405 by ripperpc » Thu, 2020-02-27 05:53 |
3 |
by reqyparu Mon, 2021-03-29 11:43 |
|
|
Motor Saturation Point Measurement by Ebike_Ninja » Fri, 2020-02-28 18:51 |
3 |
by danilolattaro Wed, 2021-07-07 21:35 |
|
|
Access the Vesc terminal using another App (Putty?) by mikej_w » Fri, 2020-01-17 02:23 |
3 |
by vadicus Tue, 2020-01-21 02:19 |
|
|
Mid-drive ebikes? by Zoltan » Fri, 2022-01-28 16:37 |
3 |
by frank Thu, 2022-02-03 08:51 |
|
|
How do you wire one power-on push button to two VESC 6 MIIIs? by adamchicago » Mon, 2020-01-20 23:01 |
3 |
by tsharma Tue, 2021-09-14 10:14 |
|
|
FOCBOX X is not detected by sumedh » Tue, 2022-09-13 22:16 |
3 |
by frank Mon, 2022-09-19 09:18 |
|
|
What temerpature sensor and how do I use it? by evoheyax » Wed, 2018-08-29 19:22 |
3 |
by Danny Bokma Thu, 2018-08-30 19:12 |
|
|
Getting started with bus control of the VESC by Invert » Mon, 2018-05-21 12:04 |
3 |
by PM Thu, 2018-05-31 18:38 |
|
|
360 Rotation Hall Sensors, would these work through ADC? by portnawake » Thu, 2018-06-07 02:37 |
3 |
by Roger Wolff Fri, 2018-06-15 08:50 |
|
|
Sensorless Transition and Deadtime Distortion by vadicus » Wed, 2020-09-16 21:54 |
3 |
by vadicus Tue, 2020-10-13 07:29 |
|
|
VESC Classic 100V shutting down by floh349 » Thu, 2026-08-27 13:44 |
3 |
by floh349 Sat, 2026-10-10 14:05 |
|
|
Programming NRF51822 Module with ST-Link v2 by koralle » Wed, 2018-07-11 12:06 |
3 |
by koralle Sun, 2018-07-15 01:28 |
|
|
Electric motor from car alternator by frontaleducation » Sun, 2020-11-08 19:39 |
3 |
by frontaleducation Tue, 2020-11-24 14:41 |
|
|
Stutter start by benha » Tue, 2021-08-17 14:30 |
3 |
by flyingbrike Wed, 2021-09-08 13:45 |
|
|
Maximum cable lengths between VESC, battery pack and motor? by sandersesurf » Sun, 2024-01-14 07:55 |
3 |
by bww129 Fri, 2024-03-15 05:46 |
|
|
Set and store Current limit via Canbus by matrixgti » Mon, 2019-08-19 23:13 |
3 |
by Rbz Sun, 2020-05-31 13:44 |
|
|
Input wizard and/or firmware not working for Mini ESC 4.2 with PPM input? by mshipowick » Thu, 2021-06-17 02:08 |
3 |
by mshipowick Thu, 2021-06-24 20:34 |
|
|
FSESC6.6 and Rpi via UART - Understanding the software by gabrielredding » Sat, 2019-07-06 02:50 |
3 |
by abrac Mon, 2019-07-29 14:11 |
|
|
IMU 9250 and 6050 not working on new vesc 4.12 and 4.20 by trung_qly » Sun, 2021-09-05 16:11 |
3 |
by spatsirk Mon, 2025-06-09 18:55 |
|
|
wand brake to reverse by michmg » Tue, 2019-09-10 23:54 |
3 |
by michmg Sat, 2019-09-14 20:16 |
|
|
VESC 75/300 vs VESC 100/250 by XBO » Tue, 2021-09-07 19:31 |
3 |
by flyingbrike Wed, 2021-09-08 13:42 |
Log in to post new content in the forum.
