You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
VESC OLED Display without arduino by georgeli293 » Wed, 2024-01-10 19:36 |
3 |
by vadicus Thu, 2024-01-11 22:24 |
|
|
lower power output than expected by mxpro32 » Tue, 2019-06-18 21:38 |
3 |
by frank Sun, 2019-07-21 18:39 |
|
|
Type of Hall sensor by Faheem » Thu, 2023-10-12 05:52 |
3 |
by Faheem Mon, 2023-10-23 10:02 |
|
|
[Solved]Command the throttle (ADC1) with a DAC by captaintoon » Sat, 2024-01-27 23:41 |
3 |
by captaintoon Sun, 2024-01-28 15:44 |
|
|
Analog Throttle/Brake -- ADC2 does NOT cut power to the throttle? What is wrong? by 010203040506070809 » Fri, 2019-09-20 07:57 |
3 |
by striderkent Fri, 2019-09-20 21:54 |
|
|
understanding switching frequency and dutycycle by speed3r » Thu, 2019-08-08 13:36 |
3 |
by speed3r Thu, 2019-08-15 09:26 |
|
|
Regen not enabling! by Fpvlee » Sun, 2021-07-25 01:11 |
3 |
by lilysmith1098 Fri, 2022-07-29 09:45 |
|
|
Runaway on throttle disconnection by DavidBike » Sat, 2021-06-05 15:44 |
3 |
by vadicus Sun, 2021-06-06 22:11 |
|
|
Set McConf with no values --> bootloader erased? by Kakskiv » Tue, 2017-11-28 12:52 |
3 |
by basti30 Wed, 2018-08-22 22:22 |
|
|
Open source hardware? by Jens » Thu, 2017-09-14 18:15 |
3 |
by frank Fri, 2017-09-15 14:01 |
|
|
EBike "Throttle" / "Brake" Wiring Questions by oSPANNERo » Sun, 2022-02-27 16:07 |
3 |
by Jamesavery22 Sat, 2024-12-21 19:27 |
|
|
vesc control with 0-5v analog input... and general motor/esc recomendation by rcjustin » Thu, 2022-03-03 03:33 |
3 |
by j.konrad Fri, 2022-03-04 01:09 |
|
|
Ideal Thermistor/Temperature Sensor? by josh » Sat, 2017-10-14 07:07 |
3 |
by josh Sun, 2017-10-22 06:52 |
|
|
Newbie - controller/motor not working by JLow75 » Tue, 2018-11-13 09:50 |
3 |
by bsissell Fri, 2021-11-26 07:17 |
|
|
CAN Bus Control by External Host by josh » Fri, 2018-11-30 06:43 |
3 |
by Jack_Li Mon, 2019-07-01 10:37 |
|
|
Motor dosent run normaly, it jerky like crazy. by lumosi » Fri, 2021-03-05 20:36 |
3 |
by dsuresh Wed, 2021-03-10 19:54 |
|
|
Trampa 100/250 with one old brushed DC motor....how can i change the motor spin direction????plz help!!! by Asi » Fri, 2022-11-18 12:45 |
3 |
by frank Sat, 2022-11-19 14:55 |
|
|
speed controller at low RPM by hagoston » Mon, 2021-03-08 13:54 |
3 |
by Elwin Sun, 2021-10-31 13:53 |
|
|
Always get Fault:DRV in FOC mode during startup . by stone_1706 » Sat, 2019-02-02 17:35 |
3 |
by stone_1706 Tue, 2019-02-12 03:20 |
|
|
Completely disabling regen current possibility on vesc by riraheta » Tue, 2022-11-29 01:48 |
3 |
by frank Wed, 2022-11-30 09:33 |
|
|
Sub zero temperature VESC412 issues by jetigm » Fri, 2019-02-08 21:12 |
3 |
by sam.vanratt Sun, 2019-02-10 14:07 |
|
|
impossible to post new feature request by player107 » Wed, 2022-12-07 08:15 |
3 |
by frank Fri, 2022-12-09 14:28 |
|
|
Position accuracy by wall0069 » Sat, 2018-12-22 00:25 |
3 |
by sam.vanratt Thu, 2018-12-27 20:39 |
|
|
Bldc generator voltage control by Gsorter » Fri, 2022-12-09 23:52 |
3 |
by frank Wed, 2023-01-04 18:39 |
|
|
Which to believe, manufacturer inductance spec or VESC autodetection? by kubark42 » Wed, 2021-09-29 15:59 |
3 |
by kubark42 Fri, 2021-10-22 20:01 |
Log in to post new content in the forum.
