You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
What is a common motor efficiency? I'm at 72% by ever.summer » Tue, 2019-05-28 05:02 |
5 |
by Roger Wolff Sun, 2019-06-02 10:19 |
|
|
VESC on DIY CNC router by tbartoletta » Wed, 2019-02-20 03:00 |
5 |
by GunnarW Thu, 2019-02-21 16:44 |
|
|
VESC safety by alexantosh » Tue, 2021-11-23 15:47 |
5 |
by alexantosh Tue, 2021-12-28 15:10 |
|
|
Anti spark connector burnt my vesc? by v71n24908c27h8bn9 » Mon, 2022-07-04 12:39 |
5 |
by Spaceman Wed, 2022-07-13 16:26 |
|
|
step/dir by blueflower » Thu, 2020-01-16 04:15 |
5 |
by akkoxe Mon, 2022-08-08 06:34 |
|
|
Previous tool+5.2 by Phill Dixon » Sun, 2022-05-01 07:50 |
5 |
by firemaxx Thu, 2024-07-18 09:10 |
|
|
Cannot change CAN Baudrate, Maytech SUPERFOC6.8 by sivanhere » Thu, 2023-03-23 08:12 |
5 |
by frank Mon, 2023-03-27 09:28 |
|
|
VESC TOOL ADC Voltage mapping too low. SOLVED by Ecyclist » Fri, 2018-10-19 22:38 |
5 |
by sam.vanratt Thu, 2018-11-22 20:21 |
|
|
AC Synchronous motor support by Dark » Mon, 2019-07-29 15:03 |
5 |
by rizanirusli Wed, 2021-05-05 08:39 |
|
|
Motor shutting off due to FAULT_CODE_ABS_OVER_CURRENT by isso777 » Mon, 2022-01-24 13:56 |
5 |
by canoeman Thu, 2022-01-27 18:12 |
|
|
Vesc Max current 90A Vs ESC Max current 135A? by ScootScoot » Tue, 2021-12-14 13:00 |
5 |
by Markula Thu, 2021-12-16 20:42 |
|
|
IMPSM Motor and Gearing by baein » Tue, 2022-01-25 11:19 |
5 |
by Rohan_Suresh_babu Sat, 2024-03-02 12:18 |
|
|
No, BLDC is not dead. by Pimousse » Wed, 2019-06-12 17:41 |
5 |
by hexakopter Sat, 2020-04-18 12:30 |
|
|
Hall sensor table by spacemango » Tue, 2020-06-16 15:47 |
5 |
by pf26 Tue, 2020-06-23 15:10 |
|
|
Pwm+dir input support by adilrepas » Tue, 2020-12-22 03:32 |
5 |
by skyline1970 Sat, 2021-02-06 19:32 |
|
|
On MOSFET choice and replacement by DarioP » Wed, 2020-09-30 14:11 |
5 |
by TheFallen Fri, 2020-10-02 10:57 |
|
|
VESC FOC detecting running flawlessly, motor flipping direction erratically when running in speed and duty mode by DMKitsch » Fri, 2020-10-23 21:59 |
5 |
by milesf Wed, 2020-11-18 06:01 |
|
|
VESC configuration with a high KV Motor by batdan » Sat, 2018-01-13 23:01 |
5 |
by Roger Wolff Sun, 2018-02-04 10:09 |
|
|
a motor for VESC !! by themotorman » Sat, 2018-12-29 06:19 |
5 |
by TechAUmNu Fri, 2019-11-15 14:20 |
|
|
Independent Throttle on ADC1 and Brake on ADC2? by striderkent » Tue, 2019-01-08 18:31 |
5 |
by canarispott Sun, 2021-10-31 02:44 |
|
|
trampa by badger1666 » Mon, 2017-12-11 22:37 |
5 |
by wdaehn Wed, 2017-12-13 12:17 |
|
|
Sudden kick (from motor current cut off?) by darowi » Mon, 2017-10-02 18:56 |
5 |
by darowi Tue, 2020-09-15 12:45 |
|
|
Two Motors on same Shaft by Giga93 » Thu, 2017-12-14 10:12 |
5 |
by ThierryGTLTS Sun, 2017-12-17 13:20 |
|
|
Dual brushed motors from 1 R/C stick? by VESC1 » Thu, 2019-01-31 06:19 |
5 |
by sam.vanratt Sun, 2019-02-03 16:30 |
|
|
Cannot downgrade from 5.03 to 5.02 by kallep » Sat, 2022-02-26 19:08 |
5 |
by frank Sat, 2022-03-12 12:09 |
Log in to post new content in the forum.
