You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Sensorless BLDC start problem by MikeStros » Tue, 2019-07-30 11:49 |
2 |
by dekafive Fri, 2019-08-23 21:46 |
|
|
Can bus and Arduino by Snabelost » Wed, 2023-06-14 10:30 |
2 |
by Snabelost Thu, 2023-06-15 08:37 |
|
|
limits to reprogramming VESCs by wjpremerlani » Wed, 2023-06-21 09:11 |
2 |
by wjpremerlani Thu, 2023-06-22 20:13 |
|
|
Remote not receiving telemetry data by jasson » Sun, 2022-02-06 04:21 |
2 |
by jasson Sun, 2022-02-06 05:56 |
|
|
External IMU and Bluetooth by Montaire » Mon, 2020-04-27 11:57 |
2 |
by Montaire Sat, 2020-06-20 13:13 |
|
|
ws8212 and VESC firmware by dannlh » Fri, 2017-11-03 04:17 |
2 |
by dannlh Sat, 2017-11-04 18:47 |
|
|
motor not running smoothly, it makes little "steps" by nomadaomni » Mon, 2024-11-18 15:08 |
2 |
by nomadaomni Tue, 2024-11-19 12:51 |
|
|
VESC HD60T CAN DUTY CYCLE CONTROL by v1n23nt » Thu, 2022-02-17 09:39 |
2 |
by v1n23nt Mon, 2022-03-14 16:54 |
|
|
Vedder forums or Vesc forums? by Eric » Wed, 2017-09-13 14:39 |
2 |
by frank Mon, 2017-09-18 10:12 |
|
|
ESP32 VESC controller by Ortsac » Fri, 2022-01-21 18:50 |
2 |
by Gatze Wed, 2022-03-23 10:50 |
|
|
How to connect 5 Pin Hall Sensor to 6 Pin Hall Sensor Connector by tinytuna38 » Thu, 2024-06-20 20:56 |
2 |
by Nineballshot Mon, 2024-11-25 02:38 |
|
|
Flipsky 75100 controller not producing the same amount of power as esc controller at same current by Ashton » Mon, 2021-12-06 21:18 |
2 |
by Liam Li Sun, 2022-03-06 20:31 |
|
|
Loud noises at some RPMs by isso777 » Mon, 2022-01-24 16:05 |
2 |
by isso777 Tue, 2022-01-25 10:36 |
|
|
Axial Flow Pump Project by design@imsltd.co.nz » Thu, 2021-12-09 02:05 |
2 |
by design@imsltd.co.nz Fri, 2021-12-10 01:51 |
|
|
Low RPM with Hoverboard hub motor by e m i l » Wed, 2020-05-13 13:06 |
2 |
by pf26 Thu, 2020-06-18 20:53 |
|
|
Motor rotation direction by e-biker » Fri, 2017-12-22 15:02 |
2 |
by e-biker Tue, 2018-01-02 13:15 |
|
|
What do you need on your computer to run the vesc tool by Phill Dixon » Wed, 2017-10-04 21:00 |
2 |
by Tampaesk8er Wed, 2017-10-18 23:22 |
|
|
FAULT_CODE_DRV by protontim » Fri, 2017-10-06 04:19 |
2 |
by protontim Tue, 2017-10-10 22:34 |
|
|
A real Noob Question by donrecardo » Sat, 2020-05-23 16:56 |
2 |
by donrecardo Fri, 2020-06-05 10:38 |
|
|
External MPU not working. by PrestoThePirate » Thu, 2020-05-28 15:59 |
2 |
by Neato Sun, 2023-08-06 22:27 |
|
|
VESC Hardware Design For 4 in 1 Quadcopter ESC Board? by aklimaj » Wed, 2021-01-06 22:55 |
2 |
by thefallen Mon, 2021-01-11 08:38 |
|
|
Encoder over SPI doesn't work on FW3.40: SOLVED by john » Mon, 2018-11-12 09:00 |
2 |
by john Fri, 2018-11-23 16:40 |
|
|
Which App to use and how to wire it by philboslaggins » Sat, 2022-11-05 16:20 |
2 |
by nando Fri, 2025-08-29 15:19 |
|
|
ADC1 reads incorrect values by dsuresh » Tue, 2021-02-23 00:51 |
2 |
by dsuresh Mon, 2021-03-01 20:37 |
|
|
Fried Hall Effect Throttle Sensor by cdw3423vesc » Thu, 2018-11-15 05:16 |
2 |
by sam.vanratt Thu, 2018-11-22 20:33 |
Log in to post new content in the forum.
