You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Real RPM=0 but ERPM>0 issue by cir7 » Tue, 2022-07-12 20:17 |
2 |
by cir7 Wed, 2022-07-13 11:43 |
|
|
Type of motors supported by VESC 6 MKIV by Sami Sahli » Thu, 2020-06-25 11:57 |
2 |
by Samuelx Tue, 2021-08-17 20:24 |
|
|
AS5048A and the AS5047D Problems. by raess » Wed, 2018-04-04 14:05 |
2 |
by liqikai Thu, 2018-09-13 10:47 |
|
|
Can bus and Arduino by Snabelost » Wed, 2023-06-14 10:30 |
2 |
by Snabelost Thu, 2023-06-15 08:37 |
|
|
limits to reprogramming VESCs by wjpremerlani » Wed, 2023-06-21 09:11 |
2 |
by wjpremerlani Thu, 2023-06-22 20:13 |
|
|
<SOLVED> Terms defined / bldc "vs." vesc_tool by Gos1 » Tue, 2023-06-27 12:32 |
2 |
by Gos1 Fri, 2024-01-26 10:54 |
|
|
Axiom with SIN/COS encoder and Motoenergy ME1304 by Boben » Sat, 2021-03-20 20:51 |
2 |
by Boben Sun, 2021-03-21 10:03 |
|
|
VESC 100/250: analog regen brake AND e-brake cut switch? by fatty » Thu, 2021-05-13 01:16 |
2 |
by frank Mon, 2022-05-02 09:11 |
|
|
Custom code changes- I/O pin go high or low by dsuresh » Thu, 2021-05-13 19:50 |
2 |
by dsuresh Fri, 2021-05-14 22:30 |
|
|
just receaved my awesome new vesc 6 plus however it wont configurate i get an errot message. :( by sabladask » Wed, 2023-05-03 16:15 |
2 |
by frank Fri, 2023-05-05 20:54 |
|
|
Battery to motor voltage by fazekas » Sat, 2021-05-15 16:03 |
2 |
by fazekas Sun, 2021-05-16 20:43 |
|
|
Gyro/Accel utilisation for built in Alarm ?! :D by yoodog » Tue, 2021-03-30 00:48 |
2 |
by yoodog Tue, 2021-03-30 01:07 |
|
|
Motor is "pumping" under load in current control mode. is this normal? by etienne » Sat, 2023-05-13 17:16 |
2 |
by iv.kravchenko Sat, 2023-05-20 08:31 |
|
|
Update FW on multiple VESC pcbs using CAN issue by Offline » Wed, 2021-05-19 15:07 |
2 |
by Offline Wed, 2021-05-26 08:23 |
|
|
4wd rover using hub-motors by mhyer » Thu, 2023-05-18 09:56 |
2 |
by velolac Tue, 2023-05-23 10:03 |
|
|
How can I make status packet, using arduino? by Medist » Thu, 2023-06-01 07:33 |
2 |
by toboli Thu, 2023-06-01 23:06 |
|
|
Reverse polarity with 12V battery on Vesc 6, now giving fault codes by Kokonenen » Tue, 2023-03-28 13:45 |
2 |
by frank Wed, 2023-03-29 09:56 |
|
|
Help rc car bldc configuration vesc 4.20 by Katt » Sun, 2021-04-18 15:25 |
2 |
by spacewalker Tue, 2021-05-11 13:01 |
|
|
Fault finding on failed VESC This topic has been moved to "Third Party Hardware" (View topic) |
|||
|
Can I use 12V power supply? by ryde6 » Sun, 2021-04-25 08:19 |
2 |
by vadicus Wed, 2021-07-14 21:01 |
|
|
Remote not receiving telemetry data by jasson » Sun, 2022-02-06 04:21 |
2 |
by jasson Sun, 2022-02-06 05:56 |
|
|
How trottle input by wire? by Heimfried » Mon, 2020-01-27 17:49 |
2 |
by Heimfried Mon, 2020-01-27 21:43 |
|
|
motor not running smoothly, it makes little "steps" by nomadaomni » Mon, 2024-11-18 15:08 |
2 |
by nomadaomni Tue, 2024-11-19 12:51 |
|
|
How does VESC measure the flux? by Jongwon » Thu, 2020-01-30 04:45 |
2 |
by pf26 Mon, 2020-02-10 16:18 |
|
|
VESC HD60T CAN DUTY CYCLE CONTROL by v1n23nt » Thu, 2022-02-17 09:39 |
2 |
by v1n23nt Mon, 2022-03-14 16:54 |
|
Log in to post new content in the forum.
