You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
IMU support and alternate IMU ICs (Bosch bmi160?) by shaman » Fri, 2019-09-20 15:04 |
2 |
by shaman Thu, 2019-10-03 19:06 |
|
|
Braking noisy on Hoverboards hubs . by lurch » Mon, 2021-11-08 15:59 |
2 |
by lurch Mon, 2021-11-15 21:35 |
|
|
Erratic braking on vesc using large hub motor. by jtechbop » Sun, 2021-09-19 06:54 |
2 |
by jtechbop Tue, 2021-10-19 20:59 |
|
|
VESC vs HobbyWing...whats going on with the AMPS? by maljan » Mon, 2021-09-20 23:34 |
2 |
by drummerboy5408 Tue, 2021-09-21 03:41 |
|
|
Can't find Configurable FOC current filter in VESC TOOL by e-biker » Sun, 2018-04-08 12:18 |
2 |
by e-biker Sun, 2018-04-08 12:55 |
|
|
ramping up RPM over uart (solved) by Davideo » Wed, 2018-02-14 13:13 |
2 |
by Davideo Thu, 2018-02-15 02:59 |
|
|
Hardware fault troubleshooting by thewho » Sat, 2020-08-15 16:50 |
2 |
by thewho Tue, 2020-08-18 00:07 |
|
|
CAN Communication Between Three or More VESCs by mksonic » Tue, 2026-05-26 03:34 |
2 |
by mksonic Wed, 2026-05-27 05:30 |
|
|
Extending current shunt amplifier voltage by TechAUmNu » Wed, 2018-04-11 00:43 |
2 |
by Roger Wolff Tue, 2018-04-17 08:56 |
|
|
Trampa 100/250 with Cyc x1pro motor high Rpm issue PLZ Help :) by Asi » Thu, 2022-07-28 10:08 |
2 |
by Asi Thu, 2022-07-28 16:12 |
|
|
Issue connecting to ESC 4.12 by Kirkness » Wed, 2020-07-08 01:40 |
2 |
by thefallen Thu, 2020-07-09 18:01 |
|
|
Motor stopped and I had to run Setup Motors FOC wizard to get it going again by JasonBear » Fri, 2025-11-14 13:24 |
2 |
by JasonBear Sun, 2025-11-16 20:41 |
|
|
Which encoders are supported? by raess » Thu, 2018-03-22 23:38 |
2 |
by raess Fri, 2018-03-23 22:58 |
|
|
VescTool version 6.06 Android latest update by Brice77 » Sun, 2025-08-31 17:24 |
2 |
by Brice77 Mon, 2025-09-01 23:55 |
|
|
Wow wow by st0r » Sat, 2022-05-07 21:45 |
2 |
by Hansherrman Sun, 2022-10-30 01:40 |
|
|
vesc6 help me learn by badger1666 » Sat, 2018-03-31 09:05 |
2 |
by badger1666 Mon, 2018-04-02 20:15 |
|
|
Noise between VESC and microcontroller by onsokumaru » Tue, 2018-04-03 21:56 |
2 |
by fourchette Tue, 2018-11-20 21:32 |
|
|
about the encoder and gimbal by qdxiatao » Fri, 2018-01-26 16:42 |
2 |
by benjamin Fri, 2018-02-23 13:44 |
|
|
drill batteries in series with Flipsky 75100 by alexkid » Sat, 2022-05-14 15:41 |
2 |
by sergioma Sun, 2025-01-05 14:34 |
|
|
Tachometer VS RPM by Davideo » Mon, 2018-02-05 03:17 |
2 |
by Davideo Tue, 2018-02-06 00:37 |
|
|
Regenerate 30V to charge 40V battery by musinov » Thu, 2021-03-18 19:25 |
2 |
by vadicus Sun, 2021-04-11 19:27 |
|
|
VESC regenerating while RPM increased by olivierskypullc... » Fri, 2019-03-08 16:32 |
2 |
by olivierskypullc... Mon, 2019-03-11 10:45 |
|
|
FloatWheel not balancing, shooting forward by EvDeck » Fri, 2023-04-14 22:16 |
2 |
by Surefire Sun, 2023-07-09 05:59 |
|
|
Can I change control mode on the fly through the UART port? by spork » Wed, 2019-03-13 02:24 |
2 |
by spork Wed, 2019-03-13 15:41 |
|
|
[SOLVED] PWM speed control at low RPM by comes04 » Sun, 2023-04-16 13:30 |
2 |
by andrej.pangerci... Mon, 2026-03-16 18:03 |
Log in to post new content in the forum.
