You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Storing VESC Tool data for later analysis by AidanNowa » Wed, 2024-06-12 15:57 |
0 |
by AidanNowa Wed, 2024-06-12 15:57 |
|
|
CAN bus rate, Flipsky Mini FSESC6.7 by christian.lees » Tue, 2022-01-18 22:57 |
0 |
by christian.lees Tue, 2022-01-18 22:57 |
|
|
vesc setup 42V 10A e-bike accu to build in a E-skatboard by olaf2273 » Fri, 2020-04-10 12:33 |
0 |
by olaf2273 Mon, 2020-04-27 15:34 |
|
|
Firmware V4.00 field oriented control motor jerk but wont spin by jordanlow » Thu, 2020-02-13 14:41 |
0 |
by jordanlow Thu, 2020-02-13 14:41 |
|
|
Large robot servo controller with VESC, how to set up position control by kisdia » Thu, 2024-09-19 17:47 |
0 |
by kisdia Thu, 2024-09-19 17:47 |
|
|
Can't Update Firmware by indianboy42 » Mon, 2024-06-17 08:54 |
0 |
by indianboy42 Mon, 2024-06-17 08:54 |
|
|
Maximum Motor RPM will not reached by Skyver » Sun, 2022-01-23 10:53 |
0 |
by Skyver Sun, 2022-01-23 10:53 |
|
|
Running PID position Control with FOC sensorless by talabo » Fri, 2021-12-03 17:21 |
0 |
by talabo Fri, 2021-12-03 17:21 |
|
|
Connecting AMT203 to Flipsky 4.20 ESC by kgeo0003 » Mon, 2022-01-24 06:44 |
0 |
by kgeo0003 Mon, 2022-01-24 09:00 |
|
|
Autonomous RC car with Focbox suddenly stops by Autocar » Mon, 2021-12-06 06:55 |
0 |
by Autocar Mon, 2021-12-06 06:55 |
|
|
Incorrect Batt Current Readings in FOC but not in BLDC by vadicus » Tue, 2020-02-25 20:06 |
0 |
by vadicus Tue, 2020-02-25 20:09 |
|
|
Read telemetry data from USB port by mlsc » Sun, 2024-10-06 22:01 |
0 |
by mlsc Sun, 2024-10-06 22:01 |
|
|
Setting RPM over UART by klay2000 » Sat, 2024-06-29 01:27 |
0 |
by klay2000 Sat, 2024-06-29 01:28 |
|
|
custom firmware by vufmihai » Thu, 2020-01-16 09:06 |
0 |
by vufmihai Thu, 2020-01-16 09:06 |
|
|
Current control performance & best way to tune Kp and Ki by jinwonchung » Thu, 2024-10-17 15:52 |
0 |
by jinwonchung Thu, 2024-10-17 15:53 |
|
|
Comms plug and leads by craig w » Fri, 2021-12-24 00:25 |
0 |
by craig w Fri, 2021-12-24 00:25 |
|
|
Do All Vescs Suck? by Zeebybaby » Sun, 2024-10-20 20:33 |
0 |
by Zeebybaby Sun, 2024-10-20 20:33 |
|
|
Variable regen braking by Gsorter » Thu, 2024-07-11 00:04 |
0 |
by Gsorter Thu, 2024-07-11 00:04 |
|
|
PAS only one signal + BLE by sifourquier » Fri, 2021-12-31 19:08 |
0 |
by sifourquier Fri, 2021-12-31 19:08 |
|
|
No sensers by Phill Dixon » Thu, 2024-10-24 18:58 |
0 |
by Phill Dixon Thu, 2024-10-24 18:58 |
|
|
General help by jskessel » Tue, 2024-07-16 20:09 |
0 |
by jskessel Tue, 2024-07-16 20:09 |
|
|
Help with FOC/PID parameter by CTSchorsch » Thu, 2020-01-23 21:57 |
0 |
by CTSchorsch Thu, 2020-01-23 21:57 |
|
|
Does PLL measure the REAL motor speed by wyk » Mon, 2020-11-23 08:34 |
0 |
by wyk Mon, 2020-11-23 08:34 |
|
|
Vesc and Arduino Interface with ppm control???? by ruthvikchanda » Mon, 2018-09-10 12:01 |
0 |
by ruthvikchanda Mon, 2018-09-10 12:01 |
|
|
HFI Tuning - "Start Voltage" Question by drummerboy5408 » Sat, 2022-11-12 03:12 |
0 |
by drummerboy5408 Sat, 2022-11-12 03:12 |
Log in to post new content in the forum.
