You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Issues running a gimbal motor by ksau » Thu, 2021-03-11 16:44 |
0 |
by ksau Thu, 2021-03-11 16:44 |
|
|
Speed control issues w. hub motors by akerblad » Sun, 2019-04-07 17:22 |
0 |
by akerblad Sun, 2019-04-07 17:22 |
|
|
3Shul 700A reporting negative current spikes by reobaird » Sat, 2023-03-25 03:22 |
0 |
by reobaird Mon, 2023-03-27 09:34 |
|
|
How turn on /off Vesc MKS 75200 by baybradyr » Mon, 2024-07-01 22:10 |
0 |
by baybradyr Mon, 2024-07-01 22:10 |
|
|
current control mode with duty cycle limit based on throttle by devin » Thu, 2020-01-16 05:45 |
0 |
by devin Thu, 2020-01-16 05:49 |
|
|
Disable wrong FET temperature sensors by Flo98 » Sat, 2024-10-19 17:49 |
0 |
by Flo98 Sat, 2024-10-19 17:54 |
|
|
Changing the Control Mode Using PPM by Nickicook4noswag » Mon, 2024-07-08 03:27 |
0 |
by Nickicook4noswag Mon, 2024-07-08 03:27 |
|
|
Additional Status Messages by louisgcr » Tue, 2021-12-21 08:04 |
0 |
by louisgcr Tue, 2021-12-21 08:04 |
|
|
Motor draws current (up to 120 A), but doesn't turn by Heimfried » Sun, 2020-03-01 22:21 |
0 |
by Heimfried Sun, 2020-03-01 22:21 |
|
|
How to setup my VESC with AD2S1205 by Vlahosthomas » Tue, 2024-10-22 10:33 |
0 |
by Vlahosthomas Tue, 2024-10-22 10:36 |
|
|
Opinion on Dual motor and FW on One by theblash » Thu, 2024-07-11 11:00 |
0 |
by theblash Thu, 2024-07-11 11:00 |
|
|
Parsing PPM data from CAN Bus by walleywalker » Sun, 2021-12-26 23:57 |
0 |
by walleywalker Sun, 2021-12-26 23:57 |
|
|
Vesc_tool running error by kwlimm » Sun, 2020-01-19 10:01 |
0 |
by kwlimm Sun, 2020-01-19 10:01 |
|
|
Closed Loop Control Not Working by Ayden1717 » Sun, 2024-07-14 19:20 |
0 |
by Ayden1717 Sun, 2024-07-14 19:20 |
|
|
Limiting Down hill speed by dbau » Sat, 2022-01-29 06:54 |
0 |
by dbau Sat, 2022-01-29 09:19 |
|
|
Arduino- UART Library Question... by arranto12 » Sun, 2022-01-02 09:57 |
0 |
by arranto12 Sun, 2022-01-02 09:57 |
|
|
Vesc 75/300 max current by a727dd » Wed, 2020-03-04 04:34 |
0 |
by a727dd Wed, 2020-03-04 04:34 |
|
|
Using the VESC6MK VI HP braking current by uropthing » Thu, 2024-07-25 13:40 |
0 |
by uropthing Thu, 2024-07-25 13:40 |
|
|
VESC apps by bosko » Thu, 2020-01-23 18:28 |
0 |
by bosko Thu, 2020-01-23 18:28 |
|
|
HFI and braking by aethyr » Thu, 2020-03-19 21:01 |
0 |
by aethyr Thu, 2020-03-19 21:01 |
|
|
VESC with Ey4 and special function by MachWas » Mon, 2024-08-12 02:34 |
0 |
by MachWas Mon, 2024-08-12 02:34 |
|
|
replacing in wheel controler with vesc 6 mk vi? by arni » Tue, 2024-11-12 15:40 |
0 |
by arni Wed, 2024-11-13 15:04 |
|
|
How to start with vesc source code ? by cmarc » Tue, 2020-01-28 15:48 |
0 |
by cmarc Tue, 2020-01-28 15:48 |
|
|
HFI with PPM in Duty Cycle by DaganWal » Fri, 2024-08-30 00:30 |
0 |
by DaganWal Fri, 2024-08-30 00:30 |
|
|
Difficulty Tuning HFI on Hoverboard Motor for Low-Speed, High-Torque Application by Ponps33 » Tue, 2024-11-19 10:29 |
0 |
by Ponps33 Tue, 2024-11-19 10:29 |
Log in to post new content in the forum.
