You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
I need clarification on connecting a Magura 0-5k Ohm Pot Twist Throttle to Tronic 250 VESC. by notahorse » Fri, 2022-06-03 08:13 |
0 |
by notahorse Fri, 2022-06-03 08:13 |
|
|
Regenerative braking in scooter Zero x11 72V dual motor 2 x 1600 w peak power 6000W by Makroman » Wed, 2020-07-08 20:00 |
0 |
by Makroman Wed, 2020-07-08 20:00 |
|
|
FOC ABS_OVER_CURRENT at high RPM by Philippe Larouche » Sat, 2026-06-06 18:24 |
0 |
by Philippe Larouche Sat, 2026-06-06 18:24 |
|
|
Hall sensor port repeatedly fried on original hardware by Rc 44 » Fri, 2025-10-24 22:44 |
0 |
by Rc 44 Fri, 2025-10-24 22:44 |
|
|
Sensorless FOC with Duty Cycle will not stop spinning by moose09876 » Mon, 2022-08-01 18:08 |
0 |
by moose09876 Mon, 2022-08-01 18:08 |
|
|
VESC as generator - settings confirmation by justinlsquire » Mon, 2022-06-06 02:44 |
0 |
by justinlsquire Mon, 2022-06-06 02:44 |
|
|
tutorial for hfi by TONY61 » Mon, 2026-06-15 17:11 |
0 |
by TONY61 Mon, 2026-06-15 17:11 |
|
|
VESC to spin motor after power up? by A_Baum92881 » Fri, 2025-10-31 06:01 |
0 |
by A_Baum92881 Fri, 2025-10-31 17:21 |
|
|
VESC Tool Android pairinglist reset with metr.at by nice2cu » Sun, 2020-08-23 12:24 |
0 |
by nice2cu Sun, 2020-08-23 12:24 |
|
|
FOC vs. BLDC by CTSchorsch » Wed, 2020-07-15 13:15 |
0 |
by CTSchorsch Wed, 2020-07-15 13:15 |
|
|
Vesc Orientation Python by flomai28 » Mon, 2025-11-10 09:44 |
0 |
by flomai28 Mon, 2025-11-10 09:44 |
|
|
Could use some help tuning for low speed by Berrie » Tue, 2025-07-15 20:24 |
0 |
by Berrie Tue, 2025-07-15 20:24 |
|
|
Dollar signs break private messages by TechAUmNu » Tue, 2018-04-24 18:09 |
0 |
by TechAUmNu Tue, 2018-04-24 18:09 |
|
|
VESC Setup - Fluctuating/Unstable Duty Cycle/eRPM/Current by liminalsunset » Thu, 2022-08-04 01:44 |
0 |
by liminalsunset Thu, 2022-08-04 01:44 |
|
|
Because..why not: Full Self Riding Skateboard (autonomous skateboard) by x78163 » Wed, 2022-06-08 17:33 |
0 |
by x78163 Wed, 2022-06-08 17:33 |
|
|
Max eRPM with latest firmware by kubark42 » Fri, 2020-07-17 19:10 |
0 |
by kubark42 Fri, 2020-07-17 19:10 |
|
|
Kaabo mantis 10 elite(minimotors) FLIPSJY 75100 DUAL ALU PCB by Musik117 » Fri, 2025-07-18 14:33 |
0 |
by Musik117 Fri, 2025-07-18 14:33 |
|
|
Tips on tuning PID for a 170mm RW170 hub motor, 15 pole-pairs, low speed, high torque, 0-3000 ERPM by PaulMakesThings » Fri, 2022-08-05 11:06 |
0 |
by PaulMakesThings Fri, 2022-08-05 11:06 |
|
|
Issue connecting to Flipsky VESC with mobile app (Firmware 6.0.6) by Gabifat » Mon, 2025-12-15 08:35 |
0 |
by Gabifat Mon, 2025-12-15 08:35 |
|
|
Sleep mode? by pcace » Wed, 2025-07-30 06:48 |
0 |
by pcace Wed, 2025-07-30 06:48 |
|
|
How to increase the +/-165A rms current limit to 250A+ rms (350-400A peak) by ev_motors » Sat, 2018-04-28 10:18 |
0 |
by ev_motors Sat, 2018-04-28 10:18 |
|
|
BRAND NEW R SPEC DUAL 6355 (4.12 VESC) SET UP ISSUES by rodriguezjoe1@b... » Mon, 2020-09-07 17:50 |
0 |
by rodriguezjoe1@b... Mon, 2020-09-07 17:50 |
|
|
Making master and slave motors communicate both ways by Sis7 » Tue, 2020-07-21 05:58 |
0 |
by Sis7 Tue, 2020-07-21 05:58 |
|
|
Question about duty cycle control Vs current control mode by hazzahodgson » Wed, 2026-01-21 08:34 |
0 |
by hazzahodgson Wed, 2026-01-21 08:34 |
|
|
flatten the curve / powerband by TONY61 » Sun, 2025-08-10 15:26 |
0 |
by TONY61 Sun, 2025-08-10 15:26 |
Log in to post new content in the forum.
