You are here
VESC6 Beta
Log in to post new content in the forum.
Topic / Topic starter |
Replies | Last post | |
|---|---|---|---|
|
Max current by RSR » Wed, 2017-07-12 09:33 |
6 |
by gpzhao Mon, 2018-02-05 23:45 |
|
|
MAX40056F as INA240 alternative by Max2 » Sun, 2022-05-08 01:03 |
1 |
by skyline1970 Thu, 2022-11-24 21:43 |
|
|
Maximum Duty Cycle by josh » Fri, 2017-07-14 02:38 |
2 |
by josh Fri, 2017-07-14 20:32 |
|
|
Maytech 75/300 R2 v.6.02 fault by Ai » Thu, 2024-05-30 17:16 |
7 |
by Ai Wed, 2024-07-03 20:42 |
|
|
Motor setup (6374-192kv) by solidgeek » Fri, 2017-06-09 23:09 |
2 |
by solidgeek Fri, 2017-06-09 23:20 |
|
|
Mounting points through the PCB by iPeel » Thu, 2017-06-15 16:07 |
3 |
by frank Thu, 2017-06-15 17:53 |
|
|
My First ride! by Necromenz » Thu, 2017-06-15 15:30 |
4 |
by josh Mon, 2017-07-17 04:25 |
|
|
New motor.... by Roger Wolff » Sun, 2017-07-23 17:19 |
4 |
by Roger Wolff Tue, 2017-08-01 08:29 |
|
|
Newer DRV8353RS instead of DRV8301? by whydoilive » Fri, 2021-04-02 10:13 |
0 |
by whydoilive Fri, 2021-04-02 10:13 |
|
|
Noob question about regulation with potentiometer by Michael Schäfer » Sun, 2017-06-25 14:39 |
2 |
by Michael Schäfer Sun, 2017-07-09 20:43 |
|
|
OKP'S BUILD - 12S FOC by okp » Thu, 2017-06-08 20:58 |
26 |
by hexakopter Tue, 2017-07-25 22:14 |
|
|
OVER CURRENT without over current? by Oyta » Thu, 2018-04-19 23:26 |
3 |
by TheFallen Sun, 2018-04-22 14:43 |
|
|
Power switch or standby mode by Dillon » Thu, 2017-09-14 16:57 |
2 |
by Dillon Sat, 2017-09-16 22:07 |
|
|
ppm controller questions. [first build] by Jacob Lord » Fri, 2017-06-09 20:44 |
1 |
by frank Fri, 2017-06-09 22:08 |
|
|
PPM Output unavailable, or not functional - Vesc6.4 by solbergen » Tue, 2018-02-27 23:45 |
1 |
by benjamin Wed, 2018-02-28 11:55 |
|
|
PPM Voltage Output? by josh » Sun, 2017-06-18 21:39 |
2 |
by wouavier Thu, 2017-11-16 10:55 |
|
|
PPM: Full Duty-Cycle at approx. 15% Throttle by el micha » Thu, 2017-08-10 11:11 |
4 |
by frank Wed, 2021-07-28 12:10 |
|
|
Probably first dead VESC SIX by Squad » Tue, 2017-06-27 14:00 |
8 |
by frank Thu, 2017-08-17 22:31 |
|
|
Problem with encoder readings with arduino by ruthvikchanda » Thu, 2018-12-06 07:04 |
0 |
by ruthvikchanda Thu, 2018-12-06 07:04 |
|
|
Remote control that works with the VESC 6 by Oyta » Thu, 2017-06-08 19:33 |
14 |
by fedestanco Fri, 2017-06-23 19:18 |
|
|
Serial Interface by dougm » Thu, 2017-08-17 04:33 |
3 |
by Pimousse Sat, 2017-08-19 10:34 |
|
|
single 6374 FOC ride log + question on temp cutoff by makevoid » Sun, 2017-06-11 23:48 |
3 |
by makevoid Tue, 2017-06-13 00:24 |
|
|
Sometimes startup problems in FOC-Mode by Michael Schäfer » Sun, 2017-07-09 20:55 |
6 |
by tobby Fri, 2018-02-09 17:44 |
|
|
Stalled startup. by Roger Wolff » Mon, 2017-06-19 15:52 |
5 |
by TechAUmNu Thu, 2020-06-11 10:54 |
|
|
throttle & braking weak by bryabee3 » Wed, 2017-08-30 09:56 |
3 |
by frank Mon, 2017-09-18 21:04 |
Log in to post new content in the forum.
